What happens when a Jayco slide out is fully in?
The controller senses the extra current demand and this signals that the slide out is either fully out or fully in. The controller then shuts off the current to the motors and engages the locking mechanism.
How to turn OFF Auto Sync on Jayco slide out?
Electronic Manual Override (Controllers C-1 and C-2 Only) NOTE: See (Fig. 5) for locations of the mode button and LEDs. 1. Press the mode button on the controller six times and hold on the seventh for five seconds to enter electronic manual override mode. 2. Use the extend/retract switch to move both motors in or out.
Can a Jayco caravan have a bedroom slide out?
Our Jayco caravan comes with a bedroom slide out. This increases our internal space a lot by being able to extend the side of the caravan when parked up. But what happens when it doesn’t want to play nicely and gets out of sync ?. Well luckily or unluckily depending how you look at it we have experienced this issue.
Why is my Lippert slide out not moving?
He explains that when the Lippert slide-out motor runs but the room doesn’t budge, the the synchronizing cylinder that pushes and pulls the room is likely jammed. He talks about the possible causes of the jam, and tells you how to troubleshoot the system to get it working again. With Dave’s help, your slide room will be moving again in no time!
What causes a Jayco slide out to retract?
This causes the slide out to slide out or retract unevenly and can cause major mechanical problems. This condition is often caused by low battery voltage.
How does the slide out work on a Jayco caravan?
The controller is programmed to provide just enough current to move the slide out to keep both motors moving at the same rate. When it reached the extremity of travel the motors can’t continue to spin and as a result they try to spin by drawing more current.
Electronic Manual Override (Controllers C-1 and C-2 Only) NOTE: See (Fig. 5) for locations of the mode button and LEDs. 1. Press the mode button on the controller six times and hold on the seventh for five seconds to enter electronic manual override mode. 2. Use the extend/retract switch to move both motors in or out.
Why are my slide outs not going in or out?
If you hear a weird noise when you try to extend the slides, it could be the pump trying to work. If you just can’t seem to make those slide outs go in or out, it is possible on most RVs to manually extend or retract the slides.
Is there an electrical problem with the slide out?
Finding an apparent electrical button, the control panel was removed and the wires for the stuck slide were placed on another slide “in/out” button. Again, there was no power to the stuck slide when the “In” was pushed. The two young mobile repair techs were now perplexed and did not have the skill to trouble-shoot the electrical issue.
Why does my slide not retract after new motor?
After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.
Is the Jayco power supply battery about flat?
Elec tests confirmed this and the battery was certainly about flat. It’s an old battery too. We don’t free camp so I don’t watch the battery condition as I don’t have a monitoring system permanently connected. I leave it on float when at home.
The controller senses the extra current demand and this signals that the slide out is either fully out or fully in. The controller then shuts off the current to the motors and engages the locking mechanism.
Why does my Jayco trailer have no power?
The two most common reasons for this are that the battery is hooked up wrong and the leads are reversed and that will blow the reverse polarity fuses in the converter OR you have a bad or tripped shortstop breaker down under the front there that by code has to be within 18″ of the battery(s).
What causes the slide on a Jayco RV to leak?
This causes the slide to leak. You need to level your side out if you look under your side out there are big screws to level it when it slides in or out need to put rv. On level ground and screws are like large bolts you need to make sure upper is slides with the lower sometimes if you are sitting on.
