What happens if you raise the temperature on a Cal spas heater?

Raise the temperature on the control panel. If the HL or HFL message appears on the control panel, the pressure may be defective. This will shut down the heater. Call your dealer or Cal Spas customer service. A heating mode may not be selected.

When did I start priming my Cal spa pump?

Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. Beginning with the 2014 product line, Cal Spas pumps have a different method of priming. See the 2014 owner’s manual for a full description. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier.

How to troubleshoot a problem with a Cal spa?

Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. 3 Power and electrical problems. 4 Heat problems 5 Jet problems 6 Water pressure problems

What’s the temp in my Cal hot tub?

I PURCHASED THE SPA BACK IN 2000 AND THIS IS THE FIRST TIME I AM HAVING ANY TROUBLE. 2 weeks later… Can someone tell me why my thermostat shows 102 and my hot tub continues to run even when I have it set on (EC) at 99 degrees.

How many Cal spas are there in California?

Cal Spas Swim Pro™ Swim & Fitness Spas allow customers to enjoy the convenience of a complete aquatic exercise regime in the comforts of their own backyard. We offer 6 different models in our Swim Pro™ line.

What should the temperature of spa water be?

Spa water heats at a rate of 3 degrees an hour wired at 110 volts and 10 degrees an hour at 220 volts. If you did not get a reading at all then continue with next test. Make sure that the heater/filter cycle is on, and the thermostat is turned all the way up doing this test.

What to do if your spa heater does not heat?

Once they are removed, tape them together; turn the thermostat dial down to the off position, and turn the power back on. Make sure the spa is on the heater/filter cycle and water is flowing from the jets, turn the thermostat dial up while watching the contactor, if it closes when doing this, then re-test the heater using the amp-meter.

What do you need to know about Cal spas?

The Cal Spas lifestyle is about more than creating a fun and relaxing place for you to enjoy the company of friends and family —it’s also about embracing a new lifestyle of health and wellness that hydrotherapy can provide.

What should the temperature be on my spa?

Contact your dealer for more assistance. If power to the spa was shut off, the temperature may have reset after the power was restored. The automatic default for temperature is 100°F. If power goes off and then comes back on, the spa may reset to factory default temperature of 100°F. Raise the temperature on the control panel.

Where are the Cal spas hot tubs located?

Cal Spas was born. Cal Spas current headquarters grew into a 1-million square foot State-of-the-Art manufacturing plant in Pomona, California. When you bask in the warm waters of your new hot tub or swim spa, you are free to let your imagination wonder while the stresses of the day disappear. Cal Spas, too, was borne of pure imagination.

How to reset spa message on calspas.com?

Press any button to reset or wait 15 minutes and spa will automatically reset. If message spa does not reset, call customer service. Insufficient water detected in heater. Spa is shut down. (Displays on third occurrence of dr message.) Follow directions for dr message and press any button to reset spa.

Cal Spas. Consumers can add a Spa Surround to any of the company’s hot tubs that makes the whole hot tub area look custom to their backyard. Cal Spas is one of the oldest manufacturers of hot tubs in North America and with that comes tremendous experience and a quality product.

What should water temp be to turn off spa?

Spa functioning is then disabled. Once water temperature is below 108°F (42.2°C), the System will then auto reset. Check for high ambient temperatures or extended pump operation.

What are the message codes on a Cal spa pump?

Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. Beginning with the 2014 product line, Cal Spas pumps have a different method of priming.

What should the temperature be when the power goes off on a spa?

What makes Cal spas different from other spas?

A Spa Experience Like No Other. The Cal Spas lifestyle is about more than creating a fun and relaxing place for you to enjoy the company of friends and family —it’s also about embracing a new lifestyle of health and wellness that hydrotherapy can provide.