What does se mean on Bullfrog spa?
Economy Mode heats the spa to the set temperature only during filter cycles. “Ec” will display solid when temperature is not current, and will alternate with temperature when temperature is current. Push “Jets 1” to shift to Standard-in-Economy Mode, indicated by “SE” alternating with the temperature. The spa.
How long does it take to drain Bullfrog spa?
Depending on the size of your spa, it should take around an hour to drain using the hot tub’s drainage spigot, or ten minutes to drain with a submersible pump. To drain using the spigot: Turn the power to the spa off at the circuit breaker. You don’t want the pumps or jets to run while there isn’t any water in the spa.
How long does it take a bullfrog hot tub to heat up?
It can take anywhere from three to eight hours to heat a hot tub. The time it takes depends on the size of the tub and heater, the temperature of the water and air, and whether you use a cover or jets. A hot tub will heat faster if the jets are on.
How many gallons is my Bullfrog Spa?
See Full Specs
| Standard Dimensions (W x L x H) | 7′ 4″ x 7′ 4″ x 36″ |
|---|---|
| Cool Down / Child Seats | 1 |
| Water Capacity (to normal fill line) | 434 Gallons (1643 Liters) |
| *Dry/Maximum Filled Weight (includes Cover) | 661 lbs./5236 lbs. (300kg/2375kg) |
| EnduraFrame Const/Full-Foam/Molded Base | Standard |
What happens in priming mode on a bullfrog spa?
During Priming Mode, the heater is not permitted to run. Keep in mind that the spa will turn on with Jets 1 during Priming Mode if it has a Circ Pump. When you exit the Priming Mode, the Circ Pump runs by itself. Means that the temperature of the water is unknown. The temperature will be displayed after the pump runs for 1 minute.
What do the error codes on a bullfrog spa mean?
These are the error codes and display messages that a Bullfrog Spa may display, along with what they mean and the action required: There will be many messages and alerts that appear on the main screen during your ownership. Many of them may be displayed in sequence. You can often reset the spa unit by pressing the “jets” button.
Why does my Bullfrog spa shut down for 15 minutes?
Means there is a possibility of dry heater or an insufficient amount of water in the heater in order to start it. The spa system will shut down for 15 minutes. Press any of the buttons in order to reset heater start-up. See box for “Flow Related Checks” down below.
How to prevent airlocks in a bullfrog hot tub?
To prevent airlocks when filling your spa, be sure to open all valves in the JetPaks and all other jets in the spa before filling to allow as much air as possible to escape from the system during the filling process. Fill your spa through the filter by taking the filter cap off and put the hose directly in the filter.
These are the error codes and display messages that a Bullfrog Spa may display, along with what they mean and the action required: There will be many messages and alerts that appear on the main screen during your ownership. Many of them may be displayed in sequence. You can often reset the spa unit by pressing the “jets” button.
During Priming Mode, the heater is not permitted to run. Keep in mind that the spa will turn on with Jets 1 during Priming Mode if it has a Circ Pump. When you exit the Priming Mode, the Circ Pump runs by itself. Means that the temperature of the water is unknown. The temperature will be displayed after the pump runs for 1 minute.
To prevent airlocks when filling your spa, be sure to open all valves in the JetPaks and all other jets in the spa before filling to allow as much air as possible to escape from the system during the filling process. Fill your spa through the filter by taking the filter cap off and put the hose directly in the filter.
Means there is a possibility of dry heater or an insufficient amount of water in the heater in order to start it. The spa system will shut down for 15 minutes. Press any of the buttons in order to reset heater start-up. See box for “Flow Related Checks” down below.
