What does it mean when spa light is blinking?
If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected. Could indicate a flow problem. LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours). Heater is shut down, but other spa functions run normally.
What does hi limit mean on a hot tub?
Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational. PSoC = Pressure switch open with circulating pump. PSoL = Pressure switch open with low pump.
Is there an error code on my hot tub?
Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa’s equipment area.
What does it mean when spa is shut down?
SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected. Could indicate a flow problem. LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).
What are the error codes on the Balboa spa?
Balboa Spa Side Error Codes pd Power supply, unit running on battery ba OH Sensors reading 112-118° F. OHH Overheat. Spa has shut down. One sensor OHS Overheat. Spa has shut down. One sensor
What does it mean when your spa sensor is out of balance?
Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. Substantial difference between temperature sensors detected. Could indicate a flow problem. Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).
What does SNS stand for in hot tub?
SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.
Where is the control panel on my hot tub?
For a control panel that is built into the hot tub if you have a look inside the service bay of the hot tub you will probably see that it is also connected to the hot tub via a cable which will no doubt be plugged in somewhere. Again check for corrosion.
How can I control my cleverspa hot tub?
Once you have successfully paired your device with your CleverSpa® hot tub, the control centre is where you will control your hot tub. Press the 365 FreezeGuard button to activate the function. Will set the heater to its lowest temperature.
Where is the service icon on coast spas TSPA MP?
Service Icon Appearing on Keypad Display 9 Service Icon and LED Displayed 13 Display is Flashing 17 Wrong Temperature Appearing on Keypad Display 20 Smart Winter Mode 23 Miscellaneous Wiring Diagram 67 Professional Repair Kit Info 68
What is error code HL for hot tub?
What is error code HL Hot tub is set to 100 degrees, when… We just moved into a new house that has a hot tub. After We just moved into a new house that has a hot tub. After about a week the hot tub no longer stays above 90 degrees even though we have it set at … read more Building Analyst and Home…
What does HL mean on Arctic Spa hot tub cover?
You can Order your new Arctic Spa Replacement Hot tub cover here. When “HL” error message displays, it means the system shut the heater down because temps at the heater reached 119ºF (48ºC).When “HL” error message is flashing, it means the system shut down because the water temps in the spa reached 112ºF (44ºC).
What does HL mean on an emerald spa?
2 years electro mechanical… Mt LED display on my Emerald Spa is saying:”HL” and no temperature number. What does this mean? It was not as hot as it should be, but would not display actual temperature.
Why do I get error messages on my Master Spa?
For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump.
