What does F2 mean on Balboa hot tub?
daily filtration
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| F2 | 4 hours daily filtration; system message, not an error |
| F4 | 8 hours daily filtration; system message, not an error |
| F6 | 12 hours daily filtration; system message, not an error |
| F | Fahrenheit, used to indicate panel is in Fahrenheit mode |
How do you unlock Catalina Spas in a hot tub?
To unlock the panel, press “Time” “Jets 1” then “Cool.” Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm” within 3 seconds to activate the lock. The TL indicator light will light when the set temperature is locked. To unlock the set temperature, press “Warm” or “Cool” then “Time,” “Jets 1” and “Cool.”
What does dry mean on a Balboa hot tub?
There is a Verified “Dry” (drY or dY) Condition in the Heater. The “dr” or “HEATER MAY BE DRY WILL RETEST SHORTLY” Fault has occurred 3 times in a row without a successful Heating Cycle and Spa Functions are Disabled. There is Not enough Water in the Heater to Start it.
How do I get my Catalina spa out of sleep mode?
Sleep mode heats the spa to within 20°F of the set temperature only during filter cycles. The “SLEEP” icon will display until mode is changed. Blower (optional) Press the “Blower” button to turn on or off. If left on, the blower will automatically turn off after 15 minutes.
Why does my hot tub say heating suspended?
Check the pump is working Finally, if your hot tub is heating it could be that your pump is not working properly. This will mean that the water is not being pumped around the hot tub, which will restrict or stop the flow. Causing the heater to cut off. And your hot tub to get cold.
What are the error codes on the Balboa spa?
Balboa Spa Side Error Codes pd Power supply, unit running on battery ba OH Sensors reading 112-118° F. OHH Overheat. Spa has shut down. One sensor OHS Overheat. Spa has shut down. One sensor
What does F2 mean on a Balboa hot tub?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. There are a few things you can look for when trouble shooting an F2 error code on your hot tub.
How to check spa panel messages on Balboa direct?
1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.
What to do if your hot tub has an F2 error code?
There are a few things you can look for when trouble shooting an F2 error code on your hot tub. First it is always a good idea to cut the power to the unit and let it cool down and then reset it. Sometimes this is all it will take to regain normal operation.
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. There are a few things you can look for when trouble shooting an F2 error code on your hot tub.
How to prevent damage to a Catalina spa?
• Replace or clean the filter cartridge regularly to remove debris and mineral buildup which may affect the performance of jets, limit the water flow, or trip the high limit thermostat which will automatically turn off the entire spa to prevent further damage to the spa. • Stay out of the spa if you have open wounds or an infections disease.
There are a few things you can look for when trouble shooting an F2 error code on your hot tub. First it is always a good idea to cut the power to the unit and let it cool down and then reset it. Sometimes this is all it will take to regain normal operation.
