What does error6 mean on a spa?

What does error6 mean on a spa?

Thermal cut-out tripped
What is Error 6? In Davey, SpaQuip, SpaNet spa controllers, Error 06 simply means “Thermal cut-out tripped.” This error indicates that the safety electromechanical over temperature cut out thermostat on the heater has tripped.

How do I reset my Spa Power 1000?

To Reset the SP400/600/601 and Xcelsior Spa Pool System wait a minimum of 20 minutes to allow the heater tube/area to cool. Then press the down, up and pump buttons all simultaneously and hold for 3 seconds. To Reset the SP800 & SP1200 wait a minimum of 20 minutes to allow the heater tube to cool.

How do you reset a spa?

How to Reset a Spa Heater

1. Locate the spa’s high-limit reset. This is a red button found on many spa packs.
2. Press the high-limit reset button.
3. Turn on your spa and observe its operation.
4. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

What does E3 mean on my hot tub?

This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c. AMBIENT AIR TEMPERATURE. SOLUTIONS, THE TEMPERATURE IS TOO LOW. Remove the pump from the spa by placing the stopper caps on the inside of the spa over the debris screens.

Why does my Spa have an error 6 code?

An error 6 code is due to no flow in the spa. Firstly make sure that all jets, waterfalls are all open. Waterfalls being closed will also result in the filtration pump not pumping enough water through to the heater.

Why is my SP1200 pool spa not working?

It sounds like some piece of equipment or a loose/faulty wire is causing the problem. However, when unplugging each piece of equipment to test what it may be you will need to re-set the control on this spa as follows: Poolservice123 : With any Error 3-8, spa operation will stop and not continue until the controller is reset.

Why does my pool have an error 6?

I have a sp1200 pool spa and an error 6 is coming up which in my manual says that it is a thermal cut out i have – Answered by a verified Pool and Spa Expert We use cookies to give you the best possible experience on our website.

Is there an air lock on SP 800?

SP 800 Press the top 4 buttons (the two light buttons and the ones underneath each one) AIR LOCK It is possible that there is an air lock in the system, especially if you have just emptied your spa and then refilled it.

Why is my spa SP600 not working properly?

Try to reset the spa. If there is still a problem then contact your spa pool reseller. This error indicates that the digital temperature sensor in the heater or pool has detected a temperature of 45 C or more. This may not be a problem with the SP600, it may be caused by excessive pump use in hot weather, or pump failure. Turn off the spa and allow

How to recover prime failed on spa power 600?

Prime failed is a special case in that it can be recovered from by pushing a button. A push of the pump button will run the pump for 60 seconds to try to get water to the heater. If successful normal operation will resume. If unsuccessful, Error 1 (H20) will be indicated on the display again. Error 2 – Not Used.

What does the spa power 600ac / BC do?

With the Spa Power 600AC/BC there is no need to program any filtration cycles, and the noise of a large jet pump running during filtration has been removed. Pump Operation. The Pump Button allows the user to control the water pump as desired when using the pool.

What does the spa power 600 alarm do?

The Spa Power 600 controller has extensive self diagnostic capabilities. In the event of a problem it will indicate an error number according to the nature of the problem. The error numbers and their meanings are listed below. Note: When in an error state the alarm can be muted by pushing theAIR/AUX button.