What does code 125 mean on Jandy aquapure?
The error code 125 is indicative that the cell will need to be cleaned and/or replaced. There are a few additional steps you can take to try and determine exactly what the issue is. 1) Inspect DC cord and cell for damage, also inspect cell for calcium buildup and debris. If damaged replace parts or entire unit.
Where do I find the service code on my aquapure?
A service code is a three digit number that appears on the display panel of an AquaPure Control Box, letting you know if your AquaPure unit is experiencing any problems. Service codes are fast, easy to read, and not only identify the problem, but direct you to an available solution.
How to check salinity of Jandy aquapure pool?
Backwash filter if a DE filter is installed. Partially drain pool and dilute with fresh water until salinity returns to 3.0 to 3.5 gpl Unit wired to improper AC voltage. Contact a pool professional Verify proper flow/temperature/salinity sensor installation. Check salinity with Myron “L” meter calibrated for NaCl or test strips.
What to do if your service code is wrong on your pool?
Conclusion: While most service codes can be solved by the pool owner, not all are immediately fixable, and if this happens it’s important to contact a local service technician who can identify and correct the error to ensure safety and warranty compliance.
The error code 125 is indicative that the cell will need to be cleaned and/or replaced. There are a few additional steps you can take to try and determine exactly what the issue is. 1) Inspect DC cord and cell for damage, also inspect cell for calcium buildup and debris. If damaged replace parts or entire unit.
Where to get help with aquapure error codes?
If you need more help understanding the AquaPure Error Codes, or need help fixing the issue, stop by a local Leslie’s Pool Supplies store and speak with a trained pool professional today. You can also request pool equipment and repair services by contacting our Pool Service and Repair Department HERE.
How to troubleshoot Jandy aquapure error code 172?
Check salinity with Myron “L” meter calibrated for NaCl or test strips. Add salt as necessary Heated sensor element not heating. (Generates 172 code) Contact a pool professional. Flow sensor temperature sensor failure. (Generates 172 code – flow sensor service) Contact a pool professional.
How to change a Jandy aquapure power supply?
3. How To Change a Jandy AquaPure Tri-Sensor Front board power supply is either too low or too high. 1. Generates code 173- Low input voltage, IF code 188 is present. 2. Generates code 170 IF 188 is not present. VAC input voltage too low. Relay not conducting in the forward direction. Relay not conducting in the reverse direction.
What to do if you get a Jandy error code?
1. Recalibrate salt reading. 2. Backwash your filter if a DE filter is installed. 3. Partially drain your pool and dilute with fresh water until salinity level returns to 3.0. 1. Typically caused by low AC voltage from back board. Check the transformer and back board.
What to do if your Jandy pool sensor is not working?
Jandy recommends that you contact a pool professional for service if you encounter a Level 2 code. Heated sensor element not heating. (Generates 172 code) Contact a pool professional. Flow sensor temperature sensor failure. (Generates 172 code – flow sensor service)
Check salinity with Myron “L” meter calibrated for NaCl or test strips. Add salt as necessary Heated sensor element not heating. (Generates 172 code) Contact a pool professional. Flow sensor temperature sensor failure. (Generates 172 code – flow sensor service) Contact a pool professional.
1. Recalibrate salt reading. 2. Backwash your filter if a DE filter is installed. 3. Partially drain your pool and dilute with fresh water until salinity level returns to 3.0. 1. Typically caused by low AC voltage from back board. Check the transformer and back board.
Jandy recommends that you contact a pool professional for service if you encounter a Level 2 code. Heated sensor element not heating. (Generates 172 code) Contact a pool professional. Flow sensor temperature sensor failure. (Generates 172 code – flow sensor service)
Which is error code is your Jandy unit displaying?
So, which error code is your Jandy unit displaying? Level 1 service codes are more common than level 2 codes and can typically be troubleshooted by the homeowner and a Jandy technical representative.
What should I do if my Jandy cell is not working?
Check DC cord 1. Clean cell if necessary 2. Check DC cord. 1. This is an indication of a bad back board. 2. Troubleshoot with Jandy or a licensed professional. Cell needs to be cleaned. 1. Troubleshoot your tri-sensor to ensure it is working properly. 2. Clean or replace cell if necessary.
What should I do if my Jandy aquapure pump is low?
Press the “test salinity” button. If salinity is low, more salt may need to be added. Clean the cell if it is dirty or clogged. Check that the unit is connected to a power supply and the pump is switched on.
So, which error code is your Jandy unit displaying? Level 1 service codes are more common than level 2 codes and can typically be troubleshooted by the homeowner and a Jandy technical representative.
Check DC cord 1. Clean cell if necessary 2. Check DC cord. 1. This is an indication of a bad back board. 2. Troubleshoot with Jandy or a licensed professional. Cell needs to be cleaned. 1. Troubleshoot your tri-sensor to ensure it is working properly. 2. Clean or replace cell if necessary.
