What are the error codes on the Balboa spa?
Balboa Spa Side Error Codes pd Power supply, unit running on battery ba OH Sensors reading 112-118° F. OHH Overheat. Spa has shut down. One sensor OHS Overheat. Spa has shut down. One sensor
How to check spa panel messages on Balboa direct?
1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.
What does it mean when your spa sensor is out of balance?
Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. Substantial difference between temperature sensors detected. Could indicate a flow problem. Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).
What are the spa side error codes for gecko?
Gecko Spa Side Error Codes FLO Pressure switch failure, switch open FLC Pressure switch failure, switch closed Prr Temp sensor failure Prh Hi-limit sensor failure HL Sensor measuring 119 degrees
Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. Substantial difference between temperature sensors detected. Could indicate a flow problem. Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).
When to use Spa when temperature is flashing?
Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational.
Are there swim spas in the Catalina Islands?
Catalina Swim Spas offer value, with features and quality from a name you can trust. So join the Catalina Swim Spa revolution where you can explore and enjoy your very own Swim Spa in the comfort and convenience of your home.
What to do when there is no fault code on Balboa?
Press any “Cool”, “Warm”, or “Temp” Button to Exit Priming Mode. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization.
When to call Balboa technical service for troubleshooting?
If the Error Repeats, Retest the “CFE” or “CONFIG ERROR” Configuration Error or Call Balboa Technical Service for Assistance. “Cyclic Redundancy Code” (CrC) Checksum Error.
What do you do at the Catalina spa?
An error occurred while retrieving sharing information. Please try again later. At Catalina Spas we believe in an overall approach to health, exercise and relaxation. Relaxing massages and hot water therapy are the best options for the person who has experienced stresses and strains throughout the day or week.
What should the water temp be at a Catalina spa?
Water temperatures between 100ºF (38ºC) and 104ºF (40ºC) are considered safe for a healthy adult. • Lower water temperatures are recommended for extended use (exceeding 10 minutes) and for young children. Extended use at higher temperatures can cause hyperthermia. • Pregnant or possibly pregnant women should consult a physician before using a spa.
If the Error Repeats, Retest the “CFE” or “CONFIG ERROR” Configuration Error or Call Balboa Technical Service for Assistance. “Cyclic Redundancy Code” (CrC) Checksum Error.
What to do if your spa has an error code?
If the problem stays SnA, then you have a bad PC board. Same with the error SnB. Find replacement PC board. Sensors are out of balance. If this alternating with the temp, it may just be a temporary condition. If the display shows only this message (blinking), the spa is shut down. Shut the spa off for 20 min to reset the power.
Is there an error code on my hot tub?
Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa’s equipment area.
1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.
What should the voltage be on a hot tub circuit board?
If you DO have 220 volts across both hot wires coming from the house, then next measure the voltage across both heating element pins. You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair.
What does message on Cal spa control panel mean?
A message on the control panel may indicate a problem. Note: The message troubleshooting shown here applies to Cal Spa control panels built in 2013 and earlier. Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual.
Why does my dead Spa have no power?
The greater disappointment is not being able to use the spa at that moment. If you’ve ever found a “dead spa” with no power, no indicator lights, nothing at all – this post is for you. Here, we outline the seven most common reasons that a hot tub has no power.
How to troubleshoot a problem with a Cal spa?
Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. 3 Power and electrical problems. 4 Heat problems 5 Jet problems 6 Water pressure problems
The greater disappointment is not being able to use the spa at that moment. If you’ve ever found a “dead spa” with no power, no indicator lights, nothing at all – this post is for you. Here, we outline the seven most common reasons that a hot tub has no power.
How to find the manufacturer of a spa?
To determine your Spas control manufacturer look at the systems electronic control box cover (front or back) for the manufacturer. Note: S ome Spa assemblers have their companies sticker over the front cover.
What to do when your spa light goes off?
Shut the spa power off, remove the filter and make sure all the jets are open. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.
Why is the blinking light on my spa not working?
Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.
