What are the error codes for a hot tub?

1) Hot Tub Error Codes (Alphabetical) * * * (3 flashing dots under temp displa Flow/Pressure switch either Open or Clos * * * (as above, & red LED lit up on boa High Limit Fault – – – , – – – ‘Watchdog’ – 48C reached, electronic fau – 01 Hi-Limit fault – 02 Temp sensor fault

Why is my Sundance Hot Tub not working?

Pressure switch open – lack of pressure OR for Sundance/Spa Builders/Balboa, pressure switch closed Substantial difference between temperature sensors detected. Could indicate a flow problem Temp above 118 degrees. High limit switch tripped Hi Limit Over Heat. Hi limit sensor is disconnected, shorted, or spa temp is above 112° F

How to check spa panel messages on Balboa direct?

1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.

What does blinking red light on hot tub control panel mean?

Blinking Red Light. A blinking red light on the control panel may indicate it needs to be reset. For most models you will turn off the power to the spa for a minute or two and then turn it back on. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

How to check the water temp in a hot tub?

• Check the water level. • Check the water temperature with an accurate temperature thermometer. Remove the spa cover and allow the water to cool. Adding cool water may be necessary. Touch any button to reset the system. If the water is still hotter than the set temperature]

What to do if your hot tub control panel is wet?

If the rice method doesn’t work, and you are convinced that your control panel is still wet, then leaving it in a warm dry spot inside for a few days may well do the trick as well. In theory at least, if moisture can get into a control panel it can also, in the right conditions evaporate out as well.

How to troubleshoot an issue with your spa?

To troubleshoot an issue with your spa, locate your specific problem in the chart below to help determine a probable cause, and then apply the right solution. Do you need to call a professional technician? Do you need to call a professional technician? Adjust the total alkalinity and pH.

When to contact an expert for a hot tub repair?

We recommend contacting an expert technician when repairs require professional attention, especially during the warranty period—you don’t want to risk voiding your warranty. Your Hot Spring hot tub offers incredible benefits for stress and tension relief, hydrotherapy, and personal connections.

Why is the heating element on my spa not working?

If for any reason one of these components fail then the required voltage to the coil will be jeopardized and the contactor will not close in order to send power to the heating element. As mentioned above, it is usually one of these components that will cause a spa not to heat.

What is the number of the Maax hot tub?

811 – The Maax Spas 811 hot tub is a family friendly hot tub with many seat levels including a deep sitting corner and a lounge. 781 – The Maax spas 781 hot tub is a hydrotherapy treat with a large capacity of seating levels including a lounge, coupled with a large amount of jets.

How big is the Maax spa model 780?

Model 780 is a spacious 7 person spa with 2 zone therapy seats, 2 Shiatsu seats and a side by side conversation area. This 91.5″ square hot tub features 2 dual speed and 1 single speed spa pump, 69 stainless steel jets and a Bluetooth music system.

What to do if your Maax Spa is not working?

Take off the heat shield cover to allow the water to cool down. Make sure that the slice valves are open and reprogram the spa to make sure there are no overlapping time cycles. Open all jets. Contact the dealer or service organization if the problem continues.

How big of a wire do you need for a Maax spa?

2. A wire connector is provided on this unit to connect a minimum 6 AWG (5.15 mm2) solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe or conduit within 5 feet (1.5m) of the unit. 3. (For cord-connected/convertible units) DANGER- Risk of injury.

What does SNS stand for in hot tub?

SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.

Is there an error code for Leslie’s pool?

Leslie’s is proud to partner with Hot Tub Works to bring you this helpful content on lesliespool.com. The best thing about digital spas and hot tubs – those with a spa side control panel – is that you are given error codes for most equipment problems.

What does hi limit mean on a hot tub?

Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational. PSoC = Pressure switch open with circulating pump. PSoL = Pressure switch open with low pump.

What are the error codes for Sundance Spas?

Sundance Spas Error Codes. COL: Temp 20F below set point. ILOC: Interlock failure – possible pump/ozone spike. FLO/FL1/FL2: Flow/Pressure switch malfunction. Hold: Panel buttons pressed to many times/quickly. HOT: PCB temperature above acceptable limit – air blower on.

Why are the jet nozzles on my hot tub not working?

The full effect of scale buildup may take some time to set in before you begin to notice significant changes in your hot tub’s performance. At first, you may start to notice the jet nozzles becoming more difficult to adjust. This is from scale buildup (calcium carbonate) settling into the eyelets of the jet nozzles.

When do Master Spa hot tub jets come out?

Plus, Master Spa Parts typically ships same day if order is placed before 3pm CST, so you can have your hot tub up and running again in no time. While frustrating, an issue with your hot tub jets or pump isn’t the end of the road for your hot tub.

Why does my hot tub keep saying HFL?

Interlock failure – possible pump/ozone spike – possibly caused by faulty ozonators, pumps and equipment Persistent low flow. (Displays on 5th occurrence of “HFL” message with 24 hours). Heater is shut down High temperature condition, has reached 110ºF.

Why do hot tub jets turn on and off?

However, when left untouched jets regulate themselves and turn on and off automatically in order to maintain the hot tub’s internal heat. Therefore, if the temperature dips below the set point, the jets will turn on until the temperature has been raised sufficiently.

What does the diagnostic logo light on a hot tub mean?

When the diagnostic logo light shines orange and gray, the spa water is within 2° Fahrenheit of the set temperature and ready to enjoy. When the spa senses an issue, the diagnostic logo light may turn off, blink, or the colors may flash independently. Specific logo light behaviors alert you to specific problems: