Is there a problem with the Goldline system?

This problem sounds very common to the Goldline system in the sense of the check system / flow / incorrect salt and the most infamous no cell power issue. There is an issue in the goldline PCB board and the factory soldered circuits giving up on the circuit board.

What should I know about the Goldline salt system?

The thing to remember is once the Goldline senses a problem with the salt system it will continuously display incorrect salt readings and functions until the problem is resolved. Once resolved it should resume proper operation, and since it doesn’t cost anything, you don’t have to invest anything to troubleshoot.

What to do if your salt cell is not working?

Below are a few tips on how to deal with salt cells that don’t work. 1. Replace or repair damaged units immediately when problems are identified. 2. Replace the entire unit every once in a while. More often than not, a well maintained and high quality system should offer decent service for up to 5 years.

Is the check system light on on my salt cell?

I replaced my salt cell (T-15) Hayward / Aquarite – I checked installation and my wiring etc. and all seems to be in order. My check system light is on and despite adding a lot of salt my reading is still saying very low salt and stuck at 2200 ppm.

Are there any problems with the Goldline salt chlorinator?

The largest problems are caused from the cells not being cleaned. Remove the cell and soak for a couple minutes in a 20-30% acid water solution but no longer or you can damage the cell. You should see bubbles as soon as you put the cell in the acid water. The life of a cell is a bit confusing. They should last MUCH longer than a year.

What to do if your salt sensor is not working?

Since the cell was too small it was not registering the salt correctly and kept asking to add salt. Check your cell to see if it is the correct one for your size pool. The sensor can also be replaced without having to replace the entire cell. It is a $20 part and is a very easy (less than 1/2 hr) fix.

Why is the no flow light on on my Aqua rite?

“No Flow” LED illuminated The Aqua Rite has sensed a no flow condition and has stopped generating chlorine. unit and that the wire is not cut or damaged. Make sure you have at least 12″ of straight pipe before the flow switch. If there is adequate flow and the LED is still on, check that

What should I do if my no flow led is flashing?

If the No Flow LED is flashing, wait 60 seconds after starting your pump and filter. Ensure there are at least 12 inches of straight pipe before the flow switch. There should be NO elbow after the flow switch. Step 1: Wait 60 seconds after the pump starts.

When to turn off LED light on Hayward Aqua rite?

Step 1: Wait 60 seconds after the pump starts. Typically, the LED light should shut off after 60 seconds. If it does not, keep reading. Step 2: Verify that you have enough straight pipe before where you have installed your flow switch. There should be at least 12″ of straight pipe before the switch.

Do you have a Goldline control panel for an Aqua Pure system?

I have a goldline control panel, … read more DOES A AQUA PURE SYSTEM THAT USES SALT NEED TO BE ASSISTED WITH CLORINE TO KEEP THE ALGAE AWAY FROM THE POOL WALLS? ALSO THE REMOTE CONTROL SHOWS THE … read more

What should I do if my pool chlorinator says no flow?

Should a low salt condition be indicated, have your salt level checked at your local pool shop. operating, you may need to manually clean your chlorinator Cell. PH and TA is a bit high but CA is on the low end so calcium shouldn’t really drop out of solution but maybe the negative charge makes it worse.

Is the chlorinator still off on my salt cell?

My salt cell is new and configured properly and all diagnostic issues check out OTHER than the fact my system still states the chlorinator is off and no flow. The pool is operating just fine and EVERYTHING else is in order.

What should I do if my Hayward Aqua rite stops producing chlorine?

The Hayward Aqua Rite has sensed a no flow condition and has stopped generating chlorine. Check that the flow switch is plugged into the connector on the bottom of the control unit and that the wire is not cut or damaged. Make sure you have at least 12″ of straight pipe before the flow switch.