Is there a problem with my caldera hot tub pump?

This doesn’t mean that there’s an issue with the pump; it simply means that you’ll have to rule some things out to get to the root of the actual problem. As always when troubleshooting, have your Owner’s Manual handy. On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool.

How many people are in the Kauai hot tub?

The Kauai hot tub seats 3 adults and features the UltraMassage ® lounge and EcstaSeat ®. Powerful spa jets and conversation seating makes the Kauai a popular 3 person hot tub. With 20 Euro jets, 5 VersaSsage ® jets and a powerful ReliaFlo ® 2.0 HP pump, the Kauai is a powerhouse of pleasure. 22 out of 23 ( 96%) reviewers recommend this product.

What kind of jets are in the Kauai hot tub?

Powerful spa jets and conversation seating makes the Kauai a popular 3 person hot tub. With 20 Euro jets, 5 VersaSsage ® jets and a powerful ReliaFlo ® 2.0 HP pump, the Kauai is a powerhouse of pleasure.

What kind of pump does the spa works use?

The Spa Works has a complete selection of Caldera Spas pumps and Caldera Spas motors. This section features replacement Caldera Spas motors, Caldera Spa pumps, and parts such as: We also offer many different configurations of Caldera Spas motors and Caldera Spas motors/pumps complete.

What to do if your circ pump is not working?

Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position. Follow the circ pump plumbing, and look for any kinks in the hose.

What to do if your hot tub circulation pump is not working?

Disconnect the plumbing and turn it on very briefly to see if any funny noises are made. Depending on the location of the problem, a replacement of the bearings, motor, entire circulation pump will be required. Pro-Tip: Your spa circulation pump should run with as little noise as possible.

What to do when power goes off on caldera spa?

Look at the spa’s LCD screen. When the screen reads “Pd”, the power has been cut off. If it is blank and the nothing on the spa will run, the circuit breaker could either be tripped or turned off. Reset the circuit breaker at the circuit box and reset the ground fault circuit interrupter on the spa. Listen to the motor and the pump.

Why are my Jets on my hot tub not working?

There is usually a very simple reason that the jets don’t have much “oomph” lately. Here’s the step-by-step process that we use in our call center to guide spa and hot tub owners through issues when their spa jets aren’t working.

What to do if your spa heater does not heat?

Once they are removed, tape them together; turn the thermostat dial down to the off position, and turn the power back on. Make sure the spa is on the heater/filter cycle and water is flowing from the jets, turn the thermostat dial up while watching the contactor, if it closes when doing this, then re-test the heater using the amp-meter.

Why is my hot tub heater not working?

Low flow in your spa or hot tub is most commonly associated with a dirty spa filter. If your spa heater won’t heat, remove and clean the filter (s) rule out a pressure or flow rate problem. Low water level, a clogged pump impeller, closed valves, clogged pipes or blocked spa drain covers can also cause flow issues.

What to do if your hot tub heater is corroded?

For spas 30-40 years old, mechanical thermostats with a capillary bulb are common. If you have a thermostat “knob” instead of a lighted red arrow, you can test your thermostat to see if the unit is faulty internally or if the sensor bulb has become corroded.

Is the hot tub supposed to be hot?

Hot tubs are meant to be HOT. If you’ve ever been in a warm tub, you know it’s just not the same. If you’re in charge of the hot tub at home, you immediately hear the complaints when the hot tub heater is not working properly.

How to troubleshoot a problem with a Cal spa?

Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. 3 Power and electrical problems. 4 Heat problems 5 Jet problems 6 Water pressure problems

When did I start priming my Cal spa pump?

Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. Beginning with the 2014 product line, Cal Spas pumps have a different method of priming. See the 2014 owner’s manual for a full description. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier.

What are the message codes on a Cal spa pump?

Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. Beginning with the 2014 product line, Cal Spas pumps have a different method of priming.

What should I do if my spa pressure switch is not working?

Put the wires back on the pressure switch. Run the spa without the filter, if you see the contactor close and you have the proper readings at the heating element then you’ve solved the problem (Replace the Filter). If removing the filter didn’t solve the problem, then the pressure switch should be replaced.

How many degrees an hour does spa water heat?

If you are getting either one of these readings, then the heating element is working properly. Spa water heats at a rate of 3 degrees an hour wired at 110 volts and 10 degrees an hour at 220 volts. If you did not get a reading at all then continue with next test.

What do you need to know about SPA will not heat?

NOTE: If you have a Printed Circuit Board (PCB) in the main control box please click here for circuit board troubleshooting. The information below is for mechanical control boxes, without circuit boards. “My spa will not heat” is the number one complaint we hear, it accounts for almost every repair that is sent in to Spa Care Center.

What should I do if my hot tub is not heating?

As you are dealing with water and electricity. The best way to check this is using a multi-metre to check the continuity of the pressure switch. If this is faulty it will need replaced and usually costs approx. £40 + labour. How to fix? If there is a fault you will need to replace the pressure/flow switch in the hot tub. 5.

What does the diagnostic logo light on caldera Utopia mean?

On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool. When the diagnostic logo light shines orange and gray, the spa water is within 2° Fahrenheit of the set temperature and ready to enjoy. When the spa senses an issue, the diagnostic logo light may turn off, blink, or the colors may flash independently.

How do you reset a hot tub control panel?

Hot tub control panels do not have reset buttons, but their spa heaters can be reset using a button. In order to fully reset the control panel, users should manually turn it off or unplug it and wait 10 to 20 seconds. However, to reset the heater, users can simply use the high-limit reset button.

What does the diagnostic logo light on a hot tub mean?

When the diagnostic logo light shines orange and gray, the spa water is within 2° Fahrenheit of the set temperature and ready to enjoy. When the spa senses an issue, the diagnostic logo light may turn off, blink, or the colors may flash independently. Specific logo light behaviors alert you to specific problems:

What does blinking red light on hot tub control panel mean?

Blinking Red Light. A blinking red light on the control panel may indicate it needs to be reset. For most models you will turn off the power to the spa for a minute or two and then turn it back on. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

What to do if your spa pump is not working?

With over 25 years of experience, we’re equipped to help with any spa issues you have or to discuss a new spa. When your spa pump is making noises… This usually happens if you recently drained the spa. Open the lock nut until you hear air hissing, then tighten up again as water begins to leak.

Why is my hot tub not running when I turn it on?

When the spa is refilled, some of that air may become trapped and act as a plug that keeps water from moving through the hot tub’s piping. If you turn on your spa, hear the pumps running, but see no water flowing from the jets, the most likely culprit is an airlock. Turn the spa off immediately to prevent damage to the heater and the pumps.

How does a caldera hot tub pump work?

In a Caldera Vacanza® Series spa, you’ll find the main pump that powers the jets and a circulating pump that maintains the water’s condition and temperature. Above both is a PVC pipe and a fitting (a union) that joins the pipes to the water pump.

Can you still get bubbles out of the spa Jets?

When running the spa, I no longer consistently get bubbles out of the jets. I do not have a blower, just an air pipe. I recall there used to be some suction at the opening of the air pipe, but it is almost undetectable now. Intermittently, I do get some bubbles out of 2 of the jets.

When do Master Spa hot tub jets come out?

Plus, Master Spa Parts typically ships same day if order is placed before 3pm CST, so you can have your hot tub up and running again in no time. While frustrating, an issue with your hot tub jets or pump isn’t the end of the road for your hot tub.

What does a gray light on a hot water heater mean?

A flashing gray light indicates that the heater high-limit thermostat has tripped, meaning that the spa water is above an acceptable temperature range or that there is a flow issue. No gray light indicates that a problem has occurred with the power supply or there is an issue with the spa control box.

Why does my hot tub have a flashing orange light?

A flashing orange light indicates a problem with the temperature sensor. No orange light means that water temperature is outside of 2° F of the set temperature. A flashing gray light indicates that the heater high-limit thermostat has tripped, meaning that the spa water is above an acceptable temperature range or that there is a flow issue.

What happens when a GFCI is tripped on a hot spring?

When a GFCI detects an anomaly in the electrical supply, such as a ground fault or a short circuit, it interrupts the circuit and cuts off all electricity to your spa. When this interruption occurs, it’s often referred to as “tripping” the GFCI.

What should I do if my GFCI goes out in my hot tub?

There may be an issue with your GFCI. Disconnect all hot tub components from your GFCI, then reset it. If it immediately trips even though nothing is attached to it, your GFCI is most likely faulty and will need to be replaced. There may be an issue with one of your hot tub’s components, such as the heater, the pumps, or the entertainment system.

What to do if your hot spring spa loses power?

Your spa’s electrical contacts have become corroded. Inspect each contact and replace any that show signs of corrosion. One or more electrical connections is loose. With the power to your spa disconnected, tug gently on each connection, then tighten and secure any that seem to be loose.

When do you turn off the jet pump on a caldera spa?

If you place the jet pump on high during the filter cycle, the filter icon will blink in the display and not resume until 10 minutes after the jet pump is shut off. Press the “Set” button to deactivate the Spa or Temperature Locks.

How do you set the timer on a caldera spa?

Press and hold down the “Set” button for three seconds until the “F1” or “F2” icon flashes in the display. Press “Light” to select between Filter Cycle 1 or 2. Then select the “Temp Up” or “Temp Down” arrows to choose the length of the filter time preferred.

How can I restore power to my hot tub?

To reset the GFCI and restore power to the spa, simply press the GFCI’s reset button. To troubleshoot issues with the temperature sensor, heater high-limit thermostat, and the spa control box, disconnect power to the spa by flipping the GFCI breaker, and leave off for thirty seconds.

Do you need GFCI breakers for Caldera hot spring?

Certain models of Hot Spring and Caldera spas (Watkins Manufacturing), require a special subpanel disconnects. These contain two separate GFCI breakers: one for the heater, and a second for the pump and other components. These spas should not be wired to a single spa circuit breaker box such as our MW disconnect panel.

Can a hot tub heater shut off all power?

Shut off all power before touching or replacing any damaged spa wiring. In some spas, the heater’s high limit switch can cause a complete power shut down. But this is what it’s meant for! The purpose of a high limit switch is to protect spa equipment (and you!) from harm.