Is the lite2 pool heater safe to use?
The Lite2 pool/spa heater is designed and manufactured to provide many years of safe and reliable service when installed, operated and main- tained according to the information in this manual and the installation codes referred to in later sections. Throughout the manual, safety warnings and cautions are identified by the ” ” symbol.
What is the installation and operation manual for a lite2 pool?
This manual provides installation and operation instructions for the Lite2 Model LJ pool and spa heaters. Read these installation and operation instruc- tions completely before proceeding with the installa- tion. Consult the Jandy factory, or local factory representative, with any questions regarding this equipment.
Do you need a carbon monoxide detector for a Jandy pool?
For indoor installations, as an additional measure of safety, Jandy Pool Products, Inc. strongly recommends installation of suitable Carbon Monoxide detectors in the vicinity of this appliance and in any adjacent occupied spaces. Improper installation and/or operation will void the warranty. H0248900F
What do I need to know about lite2 pool and spa?
• Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a nearby phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
What kind of power does a lite2 pool heater use?
The Lite2 LJ heater gets electrical power from an external 115VAC or 230VAC source and provides a dual electronic thermostat control system for pool/ spa combinations or preheat convenience. The Lite2 LJ heater is specifically designed for heating fresh water swimming pools and spas.
This manual provides installation and operation instructions for the Lite2 Model LJ pool and spa heaters. Read these installation and operation instruc- tions completely before proceeding with the installa- tion. Consult the Jandy factory, or local factory representative, with any questions regarding this equipment.
For indoor installations, as an additional measure of safety, Jandy Pool Products, Inc. strongly recommends installation of suitable Carbon Monoxide detectors in the vicinity of this appliance and in any adjacent occupied spaces. Improper installation and/or operation will void the warranty. H0248900F
• Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a nearby phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
Can a lite2 be used in a salt water pool?
The Lite2 LJ heater is specifically designed for heating fresh water swimming pools and spas. Do not use it as a general service water heater. There is a specially designed model of Lite2 for heating salt water pools. Consult your dealer for the appropriate Jandy products for these applications. 1.2 Consumer Information and Safety
How to troubleshoot Lite 2 LJ with blue wire?
For Ignitor Test,remove common probe from blue(2) wire. For Gas Valve test reinsert the common probe in with the blue(2) wire. 1) Check incoming power. (A & B) 2) Turn off incoming power. Check positioning of Conversion Block. 3) Replace Transformer. LITE 2 LJ TROUBLESHOOTING 24 VAC between Blue 1 & Blue 2 wires? YES
The Lite2 pool/spa heater is designed and manufactured to provide many years of safe and reliable service when installed, operated and main- tained according to the information in this manual and the installation codes referred to in later sections. Throughout the manual, safety warnings and cautions are identified by the ” ” symbol.
The Lite2 LJ heater is specifically designed for heating fresh water swimming pools and spas. Do not use it as a general service water heater. There is a specially designed model of Lite2 for heating salt water pools. Consult your dealer for the appropriate Jandy products for these applications. 1.2 Consumer Information and Safety
For Ignitor Test,remove common probe from blue(2) wire. For Gas Valve test reinsert the common probe in with the blue(2) wire. 1) Check incoming power. (A & B) 2) Turn off incoming power. Check positioning of Conversion Block. 3) Replace Transformer. LITE 2 LJ TROUBLESHOOTING 24 VAC between Blue 1 & Blue 2 wires? YES
