Is the Jandy legacy pool and spa heater safe?
The Legacy heater is designed and manufactured to provide many years of safe and reliable service when installed, operated and maintained according to the information in this manual and the installation codes referred to in later sections. Throughout the manual safety warnings and cautions are identified by the ” ” symbol.
Can a LRZ heater be used in a swimming pool?
The Legacy Model LRZ electronic heater is specifically designed for heating fresh water swimming pools and spas, and with proper installation and care, they will provide years of reliable service. Do not use the heater to maintain pool or spa water temperature below 70°F (21°C).
What did I do to my Jandy pool heater?
So I opened up our Jandy Legacy LRZ 399,000 to replace the insulation panels. While doing so I disconnected the unit to make examining the heat exchange easier. Once done trying to turn on the heat threw FAULT-CHECK IGN CONTROL.
What’s the fuse fault on a Jandy legacy pool?
Fuse Link Fault/Field. It’s a Jandy Legacy LRZ 399,000 BTU,. Did some googling and didn’t find much. I found this in the troubleshooting guide FAULTFUSELINK/FIELD 1. Fusible link fault.
The Legacy heater is designed and manufactured to provide many years of safe and reliable service when installed, operated and maintained according to the information in this manual and the installation codes referred to in later sections. Throughout the manual safety warnings and cautions are identified by the ” ” symbol.
The Legacy Model LRZ electronic heater is specifically designed for heating fresh water swimming pools and spas, and with proper installation and care, they will provide years of reliable service. Do not use the heater to maintain pool or spa water temperature below 70°F (21°C).
So I opened up our Jandy Legacy LRZ 399,000 to replace the insulation panels. While doing so I disconnected the unit to make examining the heat exchange easier. Once done trying to turn on the heat threw FAULT-CHECK IGN CONTROL.
Is there a check IGN control fault on Jandy LXI?
I’m getting a CHECK IGN CONTROL fault on my Jandy LXi. It will turn on and attempt to ignite a few times in 4 minutes, but it’s unable to start. Step 15 – I do not know how to check if the igniter is glowing, so I assumed NO and proceeded w/ the boxed steps.
Is the pool supply unlimited still working Jandy?
Jandy has quit the internet, but Pool Supply Unlimited is still working 7 days a week to get you the products necessary for a beautiful backyard oasis Parts for this item are available, click here.
What makes a legacy pool heater so good?
Legacy pool heaters deliver exceptional pool and spa comfort year‐round, while maximizing combustion efficiency for economical heating and are available in two models, electronic ignition and millivolt standing pilot. Copper heat exchanger and Flo‐Thru baffles provide efficient heat transfer and lower the amount of energy needed to heat your pool
Is it OK to use inauthentic Jandy replacement parts?
Use Genuine Factory Parts—It Does Matter! Using genuine Jandy factory replacement parts helps to ensure the ongoing quality and reliability of our products. Plus, the use of inauthentic parts voids all factory warranties. Inauthentic parts may appear to be suitable on the surface, but they often fall short of factory standards.
What should the water flow rate of a Jandy pool be?
Electronic Chlorine Generator. Please ensure that the salt content of the pool/spa does not exceed 4000 ppm and water flow rate is within 30-125 gpm (110-475 lpm). 1.2 consumer information and Safety
Legacy pool heaters deliver exceptional pool and spa comfort year‐round, while maximizing combustion efficiency for economical heating and are available in two models, electronic ignition and millivolt standing pilot. Copper heat exchanger and Flo‐Thru baffles provide efficient heat transfer and lower the amount of energy needed to heat your pool
Use Genuine Factory Parts—It Does Matter! Using genuine Jandy factory replacement parts helps to ensure the ongoing quality and reliability of our products. Plus, the use of inauthentic parts voids all factory warranties. Inauthentic parts may appear to be suitable on the surface, but they often fall short of factory standards.
Electronic Chlorine Generator. Please ensure that the salt content of the pool/spa does not exceed 4000 ppm and water flow rate is within 30-125 gpm (110-475 lpm). 1.2 consumer information and Safety
