How to turn off heater on Sundance spa Aqua-Tech?
Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater. Is it OK to turn the power breaker back on for 30 seconds with an empty tub or can you tell me how to shut off the heater?
How to turn off heater on Sundance Optima?
One step says: “Next, locate your spa heater, and turn it off. … Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater.
What’s the minimum temp on a Sundance spa?
Bruce, the minimum set temp on your model is 80 degrees. That being said if you want it to heat less lower your temp to 80, set your 4 filter cycles to 30min each, set your circ pump duration for 4hrs and set your spa for Economy mode.
Is the Sundance Optima a well insulated spa?
The Sundance Optima is a very well insulated spa. You still may gain some heat just because of the insulation but reducing your filter pump and circ pump cycles and keeping the spa in Economy will keep down heat that you may gain kinetically from the pumps.
When did the Sundance spa heater come out?
We are your Source for Heaters, Heater components and Complete Heater Assemblies for your Sundance® Spas. Sundance Spas Plastic Heater Assembly. Used on some 600 Series as well as 700 Series from 1987-1990. The Heater Element 6500-216 is obsolete.
What do you need to know about Sundance spa?
We have Sundance, Spas, parts, pillow, control panel, circuit board, parts, Sundance Spa pumps, Sundance Spa circuit board, Sundance Spa pcb, Sundance Spa pillows, Sundance Spa filters, Sundance Spa heaters, Sundance Spa control panel, Sundance Spa touch pad, Sundance Spa controller, Sundance Spa motor, Sundance Spa parts, filumps, sensors.
How can I Reset my Digital spa heater?
A digital spa pack may not have a manual high-temperature reset switch. This is controlled by a sensor instead. If the heater element is not getting the proper amount of water flow due to pump problems or poor water level, the sensor will trip the heater and cause it to stop operating. Check the spa’s water flow for pump operation.
What to do if your spa heater does not turn on?
Turn on your spa and observe its operation. If you do not have power to the spa, you may have a tripped breaker panel switch or GFCI outlet. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power. Turn the spa on.
Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater. Is it OK to turn the power breaker back on for 30 seconds with an empty tub or can you tell me how to shut off the heater?
Bruce, the minimum set temp on your model is 80 degrees. That being said if you want it to heat less lower your temp to 80, set your 4 filter cycles to 30min each, set your circ pump duration for 4hrs and set your spa for Economy mode.
One step says: “Next, locate your spa heater, and turn it off. … Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater.
The Sundance Optima is a very well insulated spa. You still may gain some heat just because of the insulation but reducing your filter pump and circ pump cycles and keeping the spa in Economy will keep down heat that you may gain kinetically from the pumps.
Why does my Sundance spa go into Oh error code?
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
What to do if the main pump is off in Sundance spa?
If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
What to do if your Sundance spa heater is not turning on?
Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.
Where does Sundance Spas make their hot tubs?
They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
