How to turn off heater on Sundance Optima?

One step says: “Next, locate your spa heater, and turn it off. … Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater.

How to turn off heater on Sundance spa Aqua-Tech?

Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater. Is it OK to turn the power breaker back on for 30 seconds with an empty tub or can you tell me how to shut off the heater?

Is the Sundance Optima a well insulated spa?

The Sundance Optima is a very well insulated spa. You still may gain some heat just because of the insulation but reducing your filter pump and circ pump cycles and keeping the spa in Economy will keep down heat that you may gain kinetically from the pumps.

What to do if the main pump is off in Sundance spa?

If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.

When did the Sundance spa heater come out?

We are your Source for Heaters, Heater components and Complete Heater Assemblies for your Sundance® Spas. Sundance Spas Plastic Heater Assembly. Used on some 600 Series as well as 700 Series from 1987-1990. The Heater Element 6500-216 is obsolete.

What should I do when filling my Sundance Hot Tub?

When adding new water to your Sundance hot tub, Put your hose into the filter well so that it runs through the pipes as it fills up, This will help prevent air locks upon re-start. Once your hot tub is filled, You can turn the power back on so it can begin heating up (Do not power up the hot tub until the hose has been removed).

What to do if your Sundance Spa is having trouble shooting?

Very Important: DO NOT measure by placing your probe on L1 or L2 and the other probe on Ground, you will get a 120 Volt reading which is not correct. Continuity Test or Ohms test: Turn off the power to the spa and with your probe set to a continuity check, probe the 2 heater terminals at the same time.

What kind of circulation pump does Sundance Spa use?

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

When to turn off circulation pump on Sundance spa?

Allison from November 1st to April 31st you should run the spa in Standard mode with the Circulation pump set to run 24hr duration. Between May and November depending on the ambient air temperature you may experience overheat of the water especially in July and August.

How does a Sundance spa smart heater work?

The Smart heater includes the high limit disc and the red and black wires to connect it to the circuit board. Some of the early models of the 6500-310 heaters in Sundance spas before about 2002 have a high limit temperature probe inserted into the hole beside the hi-limit disc that is connected to the circuit board.

Is there a replacement for the Sundance 6500-310 heater?

Smart low-flo heater assembly compatible replacement for the 6500-310 heater in Sundance Spas 850 and 880 series models from 2000 to current. The Smart heater includes the high limit disc and the red and black wires to connect it to the circuit board.

Is there a high limit probe on a Sundance heater?

Some of the early models of the 6500-310 heaters in Sundance spas before about 2002 have a high limit temperature probe inserted into the hole beside the hi-limit disc that is connected to the circuit board. This heater does not come with the high limit probe.

How can I tell if my Sundance Spa is having problems?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation. Is there voltage going to pump, Is there adequate Flow coming out of Heater Port in Spa?

What do you need to know about Sundance Optima?

Plus, upgraded spa cover designed for cold, harsh climates. Turn your connected home and smart devices into your personalized spa assistant, from adjusting key spa settings from anywhere, 24/7 to real-time energy reports and notifications to you and your dealer when your spa needs attention. 4.

Why is my Sundance Spa having trouble shooting?

1. Dirty Filter: even when you have cleaned the filter, the filter may be impacted and be time for a new filter. The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter.