How to troubleshoot FL1 or flashing Flo error codes?

3. First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.

How to troubleshoot a flashing Flo for a spa?

First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.

How to diagnose a Flo message on a hot tub?

Answer: When diagnosing a FLO message it is important to consider that there are 3 different types of FLO messages that your Spa’s logic is capable of displaying (a Solid FLO message, a Flashing FLO message and a Solid FLO2 message). First determine which message you are seeing.

What should I do if I get a Flo error?

1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try.

What to do if your GFCI is flashing Flo?

Make sure there is nothing in the filter area and turn your GFCI back on again. If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter.

What does a flashing Flo on a circ pump mean?

Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).

Why do I get an E02 error code on my hydro jet?

E02 ERROR CODE REASON FILTERS ARE DIRTY The E02 error code can occur when the filters are dirty or blocked. SOLUTIONS WASH OR CHANGE THE FILTERS Remove the filter cartridge from the filter housing. Using luke warm water, run the filter cartridge under the water until it runs clear.

How to troubleshoot Lite 2 LJ pool equipment?

Replace Ignitor. 1) Check incoming power. (A & B) 2) Turn off incoming power. Check positioning of Conversion Block. 3) Replace Transformer. 1) Check for short circuits. 2) Replace fuse. STEP 4 – Check Fusible Link Check wires for lose connections. Replace Ignition board. 24 VAC on white wire at Fusible Link? (4b)

When to clear the Lo fl error code?

NO WATER DETECTED ENTERING WASHER OR WATER LEVEL SENSOR TRIP NOT DETECTED (F8E1 saved The washer does not detect water input after 12 minutes of filling. The washer will drain for 8 minutes. Allow the draining error code) process to finish. The error can be cleared when the 8 minute draining process has completed.

What causes a FL2 error code on a hot tub?

Generally speaking, an FL2 error code is caused by one of two components, and for three different reasons. The first reason would be that the flow switch/pressure switch has failed and is delivering a closed circuit at all times.

How to get the Lo fl error code to go away?

Be sure the washer is in standby mode (plugged in with all indicators off). 2. After initial power is applied, wait 30 seconds before activating Service Diagnostic mode. 3. Select any three (3) buttons (except POWER) and follow the steps below, using the same buttons. Remember the buttons and the order that the buttons were pressed.

What does FL1 code mean on a spa heater?

When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock problem at the circulation pump intake.When FL2 code starts flashing it means the flow switch isn’t working and it is stuck closed. In both cases, the spa heater will deactivate.·

What causes a FL1 code on a pump?

An FL1 code can be caused by several things: Soiled filter, air lock, kinked circulation pump line, blocked circulation pump line, plugged circulation pump, bad circulation pump, plugged Flow switch, poor connection from PWA to Flow switch, bad Flow switch.

Why is the FL1 code flashing on my Sundance spa?

the TB1 terminal block and then power up the spa. If the pump doesn’t run you could have a bad pump. I have a 2004 Sundance Lagunas Spa that also has the Fl1 error code. I have had them in the past, and was able to reset it with the hose up to the intake trick on many occasions, but not this time.

What to do if you get flashing Flo error code?

1. First thing to do is remove your filter (s). If the error goes away, then it would be a good idea to replace those filters. While it is not a 100% guarantee this is your issue, it could be a contributing factor. 2. Next thing to do is open your cabinet and take a look at your flow switch.

What does flashing FL1 MSG mean on water pump?

Your assistance/suggestions is greatly appreciated. Cathy a flashing FL1 msg means the flow or psi switch is not closed when the pump is running. If you are sure your filters are not soiled you will next want to check that your water level is good ie just touching the bottom of your cushions or 3/4 of the way up your weir gate assy by the filter.

Why does my Vita spa not turn on?

Overheating condition where a water temperature sensor has detected water temperatures of 110°F (43.3°C). Spa functioning is then disabled until temps fall below 108°F (42.2°C).Could indicate a pump operating at low speed for an extended time, constant filtering due to a programming error or a faulty pump. DO NOT GET INTO THE WATER!

What does cover guy on Vita spa stand for?

The Cover Guy provides all Vita Spa replacement covers so you are guaranteed a perfect fit every time. These are the error codes and display messages that a ThermoSpas Hot Tub may display, along with what they mean and any actions required: Stands for “Overheat”- and the tub shuts down.

How do I Reset my Vita Spa hot tub?

If your Vita Spa controls stop working, the company recommends performing a system reset before troubleshooting or calling for repair. Resetting your hot tub involves pressing a particular combination of buttons on the control panel. Tap the “Prog” button until the time appears on the display. Press and hold down the “Down” arrow button.

Can You unsubscribe from a Vita spa email?

I can opt out at any time by selecting the unsubscribe option that appears at the bottom of every email. Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products.

Do you get compensation for a Vita Spa hot tub?

Hunker may earn compensation through affiliate links in this story. Hot tubs are a place for entertaining and relaxing. Vita Spa hot tubs provide a sensual, relaxing bathing experience from the comfort of your garden, deck or patio.

What to do if your jacuzzi is flashing FL-1 code?

If you have a Jacuzzi and the topside is flashing FL-1 code and the heat is not working ? This is your DIY ( How Fix My Spa VIDEO ) In this video I will show you STEP BY STEP what to look for and check to figure out what is the problem and why the heat is not working along with TIPS on how to get your Jacuzzi heating and running again…

Why does my hot tub have an error code?

Some of the most common hot tub error codes are FLO, FL1 or FL2, and are picked up by flow or pressure switches. The most common causes for this are a dirty or damaged filter, low water levels, air in the pipework or a faulty pump or sensor..