How to troubleshoot a spa side control panel?

Spaside Control Panel Buttons Not Working Correctly 1 Check for moisture under glass or on contacts 2 Check cable for any rodent damage, crimping or melting 3 Clean plug-in cable connections at both ends 4 Membrane or touch pad buttons may be faulty 5 Inspect circuit board for damage and correct power output 6 Replace topside control

Why is my spa pump not responding to my buttons?

Derek it sounds like you may have a bad remote panel. Try disconnecting the remote panel from the sensor loom inside the skirt panel. Then try your main control panel button again. If it still does’nt work you may have a bad main control panel, bad connection at the PWA or a bad PWA.

Where is the control panel on my hot tub?

For a control panel that is built into the hot tub if you have a look inside the service bay of the hot tub you will probably see that it is also connected to the hot tub via a cable which will no doubt be plugged in somewhere. Again check for corrosion.

Why does my hot tub control panel keep blinking?

If there is any condensation, dry it off. A blinking red light on the control panel may indicate it needs to be reset. For most models, you will need to turn off the power to the spa for a minute or two and then turn it back on again. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

What to do if your spa message does not reset?

Check water level in spa. Refill if necessary. Make sure pumps are been primed and filter cartridges are clean. Press any button to reset or wait 15 minutes and spa will automatically reset. If message spa does not reset, call customer service.

Why is my hot tub message not reset?

A difference in readings between temperature sensors has been detected indicating a possible water flow problem. Make sure spa is filled to proper level and that pumps are primed and filter cartridges are clean. Press any button to reset spa. If message does not reset, call customer service.

Why does my Sundance spa go into Oh error code?

Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code

Why is my spa topide control panel not working?

But there are some ways to reduce the risk… read on. Bottom line is – it could be a bad spaside control panel, or it could be a bad spa control board, or a bad cable that runs between the control panel and the control board. Or it could be fuse on the circuit board or the transformer, not sending the correct power to the topside panel.

Why are the red and green lights blinking on my spa?

If both red and green lights are blinking, this could indicate low water flow. Resetting the spa by turning off the power, waiting and turning it back on is likely to resolve the issue. If these troubleshooting tips don’t solve your problem, consult the owner’s manual for your controller. You can also contact the manufacturer for technical help.

How to troubleshoot an issue with your spa?

To troubleshoot an issue with your spa, locate your specific problem in the chart below to help determine a probable cause, and then apply the right solution. Do you need to call a professional technician? Do you need to call a professional technician? Adjust the total alkalinity and pH.

What to do if your hot tub is not working?

If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is. If the control panel simply seems not to be working you can check the connections to it and also see if any water has got in it which could be the problem.

When do I need to reset my hot tub control panel?

If your hot tub control panel isn’t working then when it can be really frustrating. Having said that, sometimes all you need to do is a simple reset on your hot tub control panel to clear the problem and to get it back into action.

Can a spa topside control work with a TV remote?

Topside controls will only work with a particular spa system control board (s). Another TV reference would be appropriate; you have to use the TV remote that is made for your make and model of television. It’s the same with spa topside controls, they only work with the spa control make and model for which they were designed.

What to do if your hot spring spa lights keep blinking?

Turn power to the spa off for 1 minute, then turn power back on. For 240 v spas, turn on the 20 amp breaker and then turn on the 30 amp breaker. For 120 v spas, plug in. If light continues to blink, Call our Spa Service Department for a service call. 413-594-2666 ext 110 My Hot Spring Spa has blinking Green and Red lights.

How to deactivate the spa lock on a hotspring?

To deactivate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-) buttons at the same time and hold them down until the word SPA and the lock symbol are no longer illuminated on the display (approximately two seconds). The TEMPERATURE LOCK feature deactivates the temperature control function of the main control panel.

Why does the spa pump turn off automatically?

The condition causes the circulation pump to turn off automatically if it’s running in order to avoid adding additional heat to spa water that could cause “Overheat” conditions. This setting is not user-programmable. This condition does not kick in until the water temperature climbs to 95°F (35°C).

Why does my hot spring spa have no power?

Ozone humming is normal. It is the vibration of ozone being sucked through the Mazzi Injector. My spa has no power or is not heating and it is a cold winter day, what do I do? If the spa has no power, or is not heating, place a droplight with a 60 or 75-watt bulb inside the access panel over pump one.