How to troubleshoot a hot tub and spa pump?
Turn off power to spa. Remove the pump and then remove the electrical housing cover on the top of the pump. Identify the faulty capacitor and replace. You will typically need a 8mm socket screwdriver and a very small flat headed screwdriver. With the new pump housing sealed and all electrics covered, turn the spa back on to dry, test the pump.
What happens if you add water to your hot tub?
It’s happened to most spa owners, you’re adding water to fill the spa or top off the hot tub, when the phone or doorbell rings. Overflowing spas usually don’t cause problems, but depending on your spa make and model, some components can become water damaged if a spa overflows.
What causes a hot tub pump to bleed?
OVERTIGHTENING COULD CAUSE DISTORTION OF PUMP HOUSING. Re-fit pump and connect unions. Tighten the unions hand tight, take a large set of grips or something similar to apply another quarter turn. Open the gate valves, release the clamped pipe and bleed pumps.
How did my hot tub drain for no reason?
I adjusted the water levels by adding more water via a garden hose, to where the water level was just above the surface skimmer inlet. I replaced the tub’s cover, and it rained all week. Today, I take off the cover and about 70 percent of the water is missing.
Why does my hot tub need to be primed?
Purge the air in your hot tub pump. Hut tubs need to be primed in order to purge air. Air restricts the pump action. You can tell when a hot tub isn’t primed properly because the motor operates, but no water flows to the jets.
What to do if your hot tub pump goes bad?
The most important first step is to never turn on the power when your hot tub is empty. If the pumps engage severe damage can happen instantly, damaging your pump beyond repair. Other tips for pump preservation include: Fill the spa by putting the hose through the filter canister.
When to turn on the power in a hot tub?
The most important first step is to never turn on the power when your hot tub is empty. If the pumps engage severe damage can happen instantly, damaging your pump beyond repair. Other tips for pump preservation include:
What does a surging hot tub pump mean?
Surging pumps can indicate the following: Water level is too low – add water according to instructions in your manual. A blockage or restriction – empty the filter basket and clean suction drain covers. 4. Pump (s) Not Priming Priming is an important process that purges air from the plumbing lines of your hot tub.
Why does my hot tub not have power?
If the power is correct here, then the terminal or cord is damaged. If high and low speeds are operating simultaneously, then remove the pump cord and then examine the pump air switch for power. If both have power then there must be wiring trouble inside which has caused a short.
How do I Turn Off the massage jets in my hot tub?
If you have massage jets running with therapy pumps and the standard circulation jets you might have a button that says: Jets 1, Jets 2, and Jets 3. To toggle the pumps on and off, simply press the jets you would like turned off. That will switch off the therapy pump you indicated.
Where is the filter pump on a hot tub?
One is leading from the filter housing into the front end of pump 1 (the filter pump) and the other is located on one side of the control box. Undo the pump unions, unplug the pump from the control box and remove the earth wire. Unscrew the pump from the supporting plywood and remove fully from the spa.
Why does my hot tub trip every time I power it up?
There are a few reasons why your GFCI might trip each time you power up your hot tub: There may be an issue with your GFCI. Disconnect all hot tub components from your GFCI, then reset it. There may be an issue with one of your hot tub’s components, such as the heater, the pumps, or the entertainment system.
How to Prime your hot tub circulation pump?
Here is a step by step guide on how to prime your hot tub circulation pump . Turn off the power switch connected to the hot tub. Take off the handle of the massage selector connected to the pump that needs priming. Slightly turn the cap of the massage selector in an anti-clockwise direction. You should hear some hissing sound coming from the pump.
How can I Reset my hot tub pump?
First, the high-limit switch should be located. It will most often be a red button located on the spa pack or the pump. This button should be pressed and will click into place. From this point, the hot tub pump has successfully been reset, and the hot tub can be turned back on.
What should I do if my GFCI goes out in my hot tub?
There may be an issue with your GFCI. Disconnect all hot tub components from your GFCI, then reset it. If it immediately trips even though nothing is attached to it, your GFCI is most likely faulty and will need to be replaced. There may be an issue with one of your hot tub’s components, such as the heater, the pumps, or the entertainment system.
