How to troubleshoot a fifth wheel landing gear problem?
I’m troubleshooting a landing gear problem on a fifth wheel. When I extend the landing gear the motor seems to make a skipping sound and has a hard time raising the trailer. I’m trying to determine if there is a gear box problem or a motor problem. I believe the legs are not bent, and there is no rear end jacks down.
Why does my landing gear not work when lowering the trailer?
In the same way, any jack – even a manual hand-crank type – requires less power (or force) when lowering the trailer than when lifting it. The cause for your powered landing gear losing steam could be any of several possibilities.
Why does my landing gear make a skipping sound?
When I extend the landing gear the motor seems to make a skipping sound and has a hard time raising the trailer. I’m trying to determine if there is a gear box problem or a motor problem. I believe the legs are not bent, and there is no rear end jacks down. Can you give me advice in determining where my problem is? Submitted: 9 years ago.
What is the weight of the landing gear?
I have a 2010 Grand Junction 340RL, Unloaded weight is advertised as 12417 with a hitch weight of 2528. I dont know the weight on the landing gear. I have seen several posts about this problem.
Why are the lights not working in my RV?
If your lights are still not working, it may be that there is no power to the light fixtures. We assume the lights in the hall and bathroom are running off of 12-volt, and that other lights in the RV are working fine. If that is the case, then check for the following possible causes: Faulty on/off switch.
Why is my landing gear not lifting my trailer?
The landing gear will operate until the feet hit the ground and puts a load on the landing gear. The fuse pops or the wiring melts. I have to use hydraulic jacks to raise and lower my trailer. I have the LIppert system with the wireless remote control.
Where is the ON / OFF switch on a RV?
Some light fixtures within an RV can have switches located on a control panel. For instance, the light fixture above our sofa has a switch near the steps, this is also where our 12v on/off switch is located. The first thing we checked was that the switch was on.
What kind of landing gear do I Need?
Stromberg Carlson A10-3376 29.5″ Lg-5 Dual Power Landing Gear Conversion Kit-29.5″ Legs, 5500 Lb. Motor . Only 6 left in stock (more on the way).
How do you retract a landing gear motor?
If you have moved the motor after attaching the gearbox to the leg, ensure that both legs are the same length before proceeding. Measure the distance from the frame to the lower end of the sliding section on the opposite leg, and extend or retract the leg with the motor attached to match. 8.
Where to buy new fifth wheel landing legs?
We stopped in at a nice RV park called Maverick Ranch in Lajitas, Texas, leaving the truck hooked up and I ordered up some new legs from Etrailer.com. I had used them in the past and was very pleased with their parts quality and customer service. They had replacements in stock from Stromberg Carlson priced at $134 each.
What was the problem with my fifth wheel?
The passenger side landing jack on our Keystone Cougar fifth wheel suffered a major failure last week. I was in the process of jacking the trailer off the truck when I heard and felt a loud clunk. In fact, my wife who was inside setting things up immediately looked out the window and ask “What the heck was that?”.
I’m troubleshooting a landing gear problem on a fifth wheel. When I extend the landing gear the motor seems to make a skipping sound and has a hard time raising the trailer. I’m trying to determine if there is a gear box problem or a motor problem. I believe the legs are not bent, and there is no rear end jacks down.
The passenger side landing jack on our Keystone Cougar fifth wheel suffered a major failure last week. I was in the process of jacking the trailer off the truck when I heard and felt a loud clunk. In fact, my wife who was inside setting things up immediately looked out the window and ask “What the heck was that?”.
We stopped in at a nice RV park called Maverick Ranch in Lajitas, Texas, leaving the truck hooked up and I ordered up some new legs from Etrailer.com. I had used them in the past and was very pleased with their parts quality and customer service. They had replacements in stock from Stromberg Carlson priced at $134 each.
In the same way, any jack – even a manual hand-crank type – requires less power (or force) when lowering the trailer than when lifting it. The cause for your powered landing gear losing steam could be any of several possibilities.
When I extend the landing gear the motor seems to make a skipping sound and has a hard time raising the trailer. I’m trying to determine if there is a gear box problem or a motor problem. I believe the legs are not bent, and there is no rear end jacks down. Can you give me advice in determining where my problem is? Submitted: 9 years ago.
I have a 2010 Grand Junction 340RL, Unloaded weight is advertised as 12417 with a hitch weight of 2528. I dont know the weight on the landing gear. I have seen several posts about this problem.
Why is my landing gear not lifting up?
Thanks. Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence.
What causes an RV slide out to not work?
A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work. If the motor-driven gearbox system is faulty, for whatever reason, your RV slide-out will not work. Your RV slide may experience resistance as it moves in and out.
A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work. If the motor-driven gearbox system is faulty, for whatever reason, your RV slide-out will not work. Your RV slide may experience resistance as it moves in and out.
Thanks. Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence.
What to do when slide outs don’t move?
Make sure the house batteries are charged completely, or if at all possible, plug your RV into shore power. This will indicate whether the problem may be the batteries or not. If you push the button for the slide outs and can hear the motor running but the slides don’t move, check the motor’s shear pins.
The landing gear will operate until the feet hit the ground and puts a load on the landing gear. The fuse pops or the wiring melts. I have to use hydraulic jacks to raise and lower my trailer. I have the LIppert system with the wireless remote control.
Why is my 5th wheel not lifting up?
If you can get access to the actual jack motor terminals and can apply 12V power (from a suitably-rated battery known to be fully charged) and you find the jack lifts properly when directly powered in this way, then you know you have a power supply issue. New cables and new clean connections all around should take care of it.
What are the common problems with fifth wheel slide outs?
Each slide-out operating system has its own unique problems. Check out the following common problems with slide-outs on a fifth wheel. A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work.
How can I extend my fifth wheel slide out?
Extend your slide-outs on the fifth wheel. Use a wire brush to remove any debris, dirt, paint chippings or rust from your slide-out tracks. Clean out all the dirt and road debris from the tracks. Apply lubricant on the gears, tracks, and rails of your slide-outs. Try and retract and fully extend your slide-out a number of times.
Each slide-out operating system has its own unique problems. Check out the following common problems with slide-outs on a fifth wheel. A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work.
Extend your slide-outs on the fifth wheel. Use a wire brush to remove any debris, dirt, paint chippings or rust from your slide-out tracks. Clean out all the dirt and road debris from the tracks. Apply lubricant on the gears, tracks, and rails of your slide-outs. Try and retract and fully extend your slide-out a number of times.
What kind of problems can a fifth wheel have?
Other problems can include a top plate that has been damaged just below the jaw pin; a rotary operating rod that has slipped out of its track; a shim which is far thicker than the recommended spec’s; or a missing handle accelerating spring. But don’t think that the issues are limited to coupling.
Can a fifth wheel be adjusted too tight?
You can also face problems if the jaws are adjusted too tight. Since we don’t want to lose trailers on the road, the fifth wheel jaws have to be adjusted to ensure a secure clamping force to provide minimal slack between the fifth wheel and the trailer. The jaw must retain its hold and allow rotation around the kingpin for turns.
Is it good to have 5th Wheel in front living room?
An often overlooked aspect of having a front living room 5th wheel is the freedom of moving the bedroom and bathroom to the rear. The rear is the place with the most space clearance between the floor and the ceiling. This translates to a bedroom and bathroom with maximum headroom that a 5th wheel can offer.
Are there any issues with 5th wheel trailers?
However, fifth-wheel trailers aren’t free of their issues; few are insurmountable, but they all warrant attention. The fifth-wheel arrangement’s primary asset is also its Achilles’ heel where some vehicles are concerned.
What happens if you hit the fifth wheel?
The end result is that most of the trailer’s weight is supported on the sharp edges of the ramp located bewteen the ramp and the ears of the fifth wheel. The trailer bolster plate will be gouged, and metal could become lodged between the trailer and the fifth wheel plate coupling surfaces.
How does a 5th wheel trailer work on a tow truck?
In essence, the trailer presses straight down on the tow vehicle’s suspension instead of levering the front wheels upward. This isn’t usually a bad thing, except that 20 percent or more of the trailer’s weight can end up borne by the front axle.
Why is my fifth wheel not working on my Tractor?
This can be caused when you park on an incline, and the mass of the trailer and its kingpin applies pressure against the lock jaw of the fifth wheel. Here, all you need to do is slowly back a tractor into the trailer to relieve the pressure.
Why does my fifth wheel make a noise when hitching up?
Chunk-k-k… Don’t let your gearbox get that bad. The first time you hear something like this when extending the legs on your fifth wheel when unhitching, or hitching up, investigate further, immediately. Upon hearing such a noise, watch the motor as you extend the legs.
When do you extend the legs on a fifth wheel?
The first time you hear something like this when extending the legs on your fifth wheel when unhitching, or hitching up, investigate further, immediately. Upon hearing such a noise, watch the motor as you extend the legs. If the motor assembly dances about in tune with the chunkity chunk chunk, the gearbox is probably going bad.
Why is my landing gear not lifting my 5th Wheel?
This is a normal occurrence. In the same way, any jack – even a manual hand-crank type – requires less power (or force) when lowering the trailer than when lifting it. The cause for your powered landing gear losing steam could be any of several possibilities.
How to repair fifth wheel landing gear DC motor gearbox?
Remove the retaining bolt from the sliding sheath on the square shaft that drives the opposite leg. Slide the sheath back to expose the gearbox drive shaft that powers leg movement. TIP: I keep a few of these bolts on hand as they can vibrate loose and disappear, causing a panic attack and the need synchronize your front leveling jacks. 2.
Are there any electrical problems in your RV?
Electrical problems in an RV or camper are very common, and often RV owners don’t know where to start when they deal with them. This article provides some basic information for the RV owner to help diagnose and repair electrical problems efficiently and safely. I’d like you to:
The first time you hear something like this when extending the legs on your fifth wheel when unhitching, or hitching up, investigate further, immediately. Upon hearing such a noise, watch the motor as you extend the legs. If the motor assembly dances about in tune with the chunkity chunk chunk, the gearbox is probably going bad.
What should I do with my fifth wheel?
After a couple cycles of forward, reverse, and some slight adjustments, you’ve positioned your fifth-wheel in the campsite. Everything is perfect. You lower your landing gear, disconnect from the hitch, and extend your slides. You start setting up some chairs around a campfire and get dinner started.
Where is landing gear on a tractor trailer?
Landing gear is also known as the stabilizers, located in the front-rear frame of the semi-trailer, it is needed when the semi-trailer is breaking away from the tractor.
