How to retract jacks on Atwood levelegs system?
Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated. Press RET and ALL to retract all jacks. 2 RED AND GREEN LIGHTS COME ON FOR A SPECIFIC JACK LOCATION Cause:
What are the flashing lights on my Atwood levelegs?
Periodically, especially if the rig has been sitting for a while, my Atwood Levelegs electric jacks will refuse to retract and will display flashing green and red lights, usually in one corner, indicating which jack is having trouble.
When did the level legs fail on my Fleetwood Bounder?
Twice, but not in-a-row, the level legs failed to fully extend on my ’06 Fleetwood Bounder. The first time I got a low voltage fault followed by a failure of the left rear leveler fault light.
Why does my Atwood leveler not shut off?
The drivers front would not extend and the balance of the levelers also stopped. Got everything retracted but alarm on leveler will not shut off when engine is on. Called dealer and he told me how to disconnect panel. Any thoughts on the problem would be greatly appreciated.
What to do if your Atwood levelegs won’t move?
If your Atwood Levelegs electric jacks quietly refuse to move, make sure that the engine is running, the rig is in park, and you have the parking/emergency brake set.
Twice, but not in-a-row, the level legs failed to fully extend on my ’06 Fleetwood Bounder. The first time I got a low voltage fault followed by a failure of the left rear leveler fault light.
How big are the power jacks on Atwood levelegs?
The size is about #22 gauge. These are signal wires only with mini Walden-Molex connectors. The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem.
Why does my Atwood RV have low voltage?
To prevent the low voltage problem the engine must be running at a little more than idle. If you try to run the jacks without the engine running, the low voltage indicator will stop the process. That makes sense. I have been having some charging issues lately. Checks indicate that the alternator is OK and it’s a brand-new chassis battery.
Where can I get an Atwood Awood controller?
Atwood Tech Service is GREAT! Do not hesitate to call if you have an Atwood problem. Other RV product mfgs. should emulate them. I need an Awood controller 66235 as mine will no longer work. Can anyone help me either repair this one or get one from a salvage yard?
Is the Atwood levelegs grounded on the same bus?
It could be a poor ground, but according to the diagram, all four motors are grounded on the same buss. Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759.
How to put Atwood levelegs system in error mode?
Put system in error mode by disconnecting one jack from power and pressing RET and ALL. Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated.
Atwood Tech Service is GREAT! Do not hesitate to call if you have an Atwood problem. Other RV product mfgs. should emulate them. I need an Awood controller 66235 as mine will no longer work. Can anyone help me either repair this one or get one from a salvage yard?
How do you extend an Atwood camper Jack?
Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated. Press RET and ALL to retract all jacks.
What to do if your camper Jack does not move?
Manually extend individual jack by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated. Press RET and ALL to retract all jacks. 2. If jacks do not move, inspect wiring at jacks and at control board to insure proper connection. KEY PAD WILL NOT TURN ON
How do I Turn On my Atwood levelegs system?
1. Disconnect power to any jack by unplugging the jack quick connect wiring at the jack motor. 2. Turn power ON to keyboard by pressing the “ON” button. 3. Press “RET” and “ALL” buttons together to put system in error. 4. The buzzer should sound on the keypad and the jack lights should be blinking red and green. 5.
What causes short Jack extension on Atwood camper?
Cause: Short jack extension followed by jack retraction. Solution: Put system in error mode by disconnecting one jack from power and pressing RET and ALL. Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack.
How to check voltage on an Atwood RV?
Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759. I have the Atwood Levelegs. To prevent the low voltage problem the engine must be running at a little more than idle.
