How to light the pilot light on your gas hot water heater?
On most hot water heaters this is a small flame or spark symbol. Once in the pilot position, press the control knob down fully and keep holding it down for 30 seconds. While holding the control button down, press the igniter button repeatedly for about 40 seconds.
How do you light a hot water heater after a flood?
Hold the pilot button down to “prime” the thermocouple—otherwise it will cut the gas supply to the pilot light. Release the pilot button, and adjust the temperature dial to “vacation” or “pilot” position. Turn the gas valve to “on” position, then slowly turn the temperature dial clockwise until the burner “fires up.”
What to do when your pilot light won’t stay lit?
Keep holding the gas knob or button down for a minute or so to ensure the pilot light gets plenty of gas flow. Slowly let go to make sure the pilot light stays lit. ONLY if you see that the pilot light is staying lit, turn the gas knob back to the On position. 2. Pilot Tube
How big should the pilot light be on a thermo couple?
The thermo couple tip should 3/8″ ABOVE the “pencil Pilot Tip”, should read about 30mv. 2. Once opened the burner door. Manufacture requires installing a new gasket around the burner door to prevent CO and air leakag.
Why is my pilot light not staying lit?
The primary reason a pilot light won’t stay lit is simply equipment malfunction. If you’ve checked everything else and the light continually goes out, this is probably the cause. In this case, you may need to replace your pilot light. A pilot light can also keep going out because of a problem with the thermocouple .
When to replace the hot water tank?
When water begins to leak from the bottom of a water heater, it is time to replace it. Leaking is a sign of corroding and wear within the tank. Most hot water heaters last for at least 10 years, and some will stay in good shape for up to 20 years.
How do you light the water heater pilot?
Turn the gas knob to “Pilot,” press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold.
Why does pilot light keep going out?
Why Does My Pilot Light Keep Going Out. The number one reason why the pilot light keeps going out is the thermocouple. Either the thermocouple is going bad or it is dirty and needs to be cleaned. Thermocouples work by producing a small amount of voltage when it is heated. This is the pilot flame that provides the heat. Nov 23 2019
Why is my hot water on pilot mode?
The pilot mode can help you to detect if there is any leakage of gas in your system. If you find your water not warm enough while on a pilot mode, then there will be a problem with your system.
Can You Leave your hot water tank on pilot?
But just to answer the question, it is always possible to leave your hot water tank on the pilot. If you are the person that has long trips and when you come back you will want to have a warm water bath, then you can make use of the pilot.
What to do if your water heater light doesnt work?
If that doesn’t work, clean it: shut off both the water heater gas valve and the main gas line near the heater. Unscrew the three nuts that hold the thermocouple and the two gas tubes to the valve. The burner is usually easy to just slide out.
Why does my pilot light keep going out on my hot water tank?
Insufficient gas in the tank is one reason for the pilot light to stop remaining lit, because while there might be enough gas trickling through the line for a tiny flame, once the burner kicks in the flame goes out because of insufficient gas. Also ensure that all the valves on the line to the heater are open so that gas is getting to the pilot.
Why is the water heater pilot light keeps going out?
There are several things that can cause your gas water heater pilot light to keep going out. One of the most common is your thermocouple. If you are unfamiliar with what this device does, the thermocouple is a device in your hot water heater that uses an electrical current to determine whether the pilot light is on or not.
