How to drain, clean and re-fill your Sundance Hot Tub?
If your hot tub has Diverter Valves, turn them to the centre position. If your hot tub has air controls, turn them to the off position. Run Jet pumps for 2 hours (make sure all jets are running and have not been manually turned off). You will need to turn the jets back on every 20 minutes. You are ready to begin draining your Sundance Hot Tub.
What to do if your Sundance Spa is having trouble shooting?
Very Important: DO NOT measure by placing your probe on L1 or L2 and the other probe on Ground, you will get a 120 Volt reading which is not correct. Continuity Test or Ohms test: Turn off the power to the spa and with your probe set to a continuity check, probe the 2 heater terminals at the same time.
What kind of circulation pump does Sundance Spa use?
Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.
What is the FL1 error code for Sundance spa Constance?
We have a Sundance Spa Constance (2011) and today also noticed the FL1 error code. In addition to the code, noticed that the pool is registering 72 degrees when it is set to 101. We have never had a problem with the hot tube, until now. We changed the UV bulb last summer and changed out the filters. Any assistance would be helpful.
How often should I drain and re-fill my Sundance Hot Tub?
Draining, cleaning and re-filling your Sundance hot tub3 or 4 times a year will ensure you are soaking in clean, clear water and minimize the amount of time and effort spent on keeping your Sundance hot tub water in great shape. Here are some tips for you to make the process as quick and easy as possible! Before Draining Your Sundance Hot Tub
Where can I get a Sundance Hot Tub?
The Sundance Spa Store is a provider of high quality Sundance Hot Tubs and Finnleo Saunas who service the GTA and Niagara Region. We deliver and service our products in cities such as Toronto, Brampton, Georgetown, Milton, Orangeville, Waterdown, Niagara Falls, Welland and Niagara On The Lake and more!
What’s the best way to drain a hot tub?
Draining your Sundance hot tub also gives you a good opportunity to give your hot tub filters a clean (or replace your Sundance Micro Clean Filters). Using a strong setting on your hose nozzle (but not a pressure washer), Spray down your paper pleated hot tub filter to wash out any debris collected inside the filter.
Is there an error code on my Sundance Hot Tub?
My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite. In the first 4 years we basically used one filter and never got this error message.
When do I get FL1 flashing on my Sundance spa?
HI, I just plugged in my Sundance spa and I’m getting the code FL1 flashing. Even before I hit any buttons. When I go to turn pump 1 on both speeds work.
How do I change the temperature on my Sundance spa?
1. Ensure your spa is in ‘Standard’ Mode. 2. Then, press the (CYCLE) button three times; The screen will display “U.” At this time the system is ready to accept your changes. 3. Press the select button and it will read “ON”. 4. Press the up or down temperature button until it reads “OFF”. 5.
If your hot tub has Diverter Valves, turn them to the centre position. If your hot tub has air controls, turn them to the off position. Run Jet pumps for 2 hours (make sure all jets are running and have not been manually turned off). You will need to turn the jets back on every 20 minutes. You are ready to begin draining your Sundance Hot Tub.
My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite. In the first 4 years we basically used one filter and never got this error message.
What do you need to know about Sundance spa?
We have Sundance, Spas, parts, pillow, control panel, circuit board, parts, Sundance Spa pumps, Sundance Spa circuit board, Sundance Spa pcb, Sundance Spa pillows, Sundance Spa filters, Sundance Spa heaters, Sundance Spa control panel, Sundance Spa touch pad, Sundance Spa controller, Sundance Spa motor, Sundance Spa parts, filumps, sensors.
What to do if you have an airlock on your Sundance spa?
Remove your filter and stick the garden hose in that hole with a rag wrapped around it to force water into that line and hopefully alleviate a potential airlock. Alternatively you could locate the suction line where it is attached to the circulation pump, loosen the gear clamp and the hose and bleed the airlock from there.
What should I use to re-fill my hot tub?
Using harsh cleaning products will result in foamy water when you re-fill your hot tub. A product such as The Tub Scrubber can be used to remove any residual waterline build up.
What should I do before draining my hot tub?
Before you begin draining your hot tub water, It is a good idea to use a Whirlpool Rinse to clean and degrease your hot tubs internal plumbing and prevent calcium build up which can affect the performance of your hot tub.
How often should I rinse my hot tub?
Simply add 250ml of Whirlpool Rinse to your hot tub water, Remove your filters & headrests (pillows) before adding Whirlpool Rinse, Run the jets (pumps) for up to 1 hour before draining the hot tub. Whirlpool Rinse is recommended once a year, Not with every water change.
What do you need to know about the Sundance spa?
As you surrender ot the warm, bubbly water of a Sundance® spa, you’ll be whisked away by the right blend of heat, buoyancy and massage that will change thehway you fee. Our patented Fluidix® jets were co-developed with Bowels Fluidics Corp, experts in the field of Fluid Dynamics.
