How to diagnose a Flo message on a hot tub?
Answer: When diagnosing a FLO message it is important to consider that there are 3 different types of FLO messages that your Spa’s logic is capable of displaying (a Solid FLO message, a Flashing FLO message and a Solid FLO2 message). First determine which message you are seeing.
What does Flo mean on a water heater?
I have an Aquacal heat pump as well. The code FLO means “Low or No Water Flow Detected”. It is a self-protection mechanism that prevents the heater from operating if there isn’t enough water moving through the heat exchanger.
What does a flashing Flo on a circ pump mean?
Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).
Why do I get trouble shoot water Flo error?
The essential reason is the water flow through the spa control device, if the water isn’t always flowing at a charge to satisfy the pressure switch, it will result in one in every of the error codes indicated above. How to trouble shoot water flo error?
Answer: When diagnosing a FLO message it is important to consider that there are 3 different types of FLO messages that your Spa’s logic is capable of displaying (a Solid FLO message, a Flashing FLO message and a Solid FLO2 message). First determine which message you are seeing.
What to do if your hot tub is not in summer logic?
Also check to see that your spa is not in Summer Logic (spa water reaches 2 DEGREES above the set temperature). If your spa is in Summer Logic, cool the water off by opening the cover and or adding some cold water to the spa. If neither of these are the case you could have a bad Flow Switch or a bad connection to the Flow Switch.
What kind of warranty does Apollo Spa have?
All spas are water tested for twelve hours to ensure that all components are working properly. With a lifetime warranty on the frame, acrylic shell and ABS bottom we stand behind our products and it shows. Apollo Spas has become one of the best-known hot tub dealers in the Northwest.
What to do when your hot tub is flashing Flo?
First determine which message you are seeing. If you are seeing a Flashing FLO message, check to see that you still have water movement ie your circulation pump is still turning/waterfall is still running, jet and blower buttons still work. If this is the case turn the GFCI breaker off to the spa and remove your filter.
Are there any free standing bathtubs at Apollo?
But at Apollo, we’re bringing back the enjoyment and relaxation that can come from a long, hot bath. Our Valencia collection Free-Standing bathtubs are easy to add to your bathroom, and with a glossy white finish and clean, simple lines, they complement any bathroom décor.
Why are Apollo long-term care bathing spas important?
At Apollo, we believe in well-being at every stage of life. Our products are focused on life-long wellness, health, revitalization and rejuvenation. Our innovative bathing spas have been developed in partnership with senior living, long-term care and health care professionals throughout the country.
What kind of tile is in an Apollo bathtub?
Vacuum formed acrylic reinforced with Fiberglass Scratch, stain and fade resistant high gloss finish. Built-in 1” tile flange on 3 sides. Right Side Drain. High Gloss Acrylic. UPC & cUPC Approved. Vacuum formed acrylic reinforced with Fiberglass Scratch, stain and fade resistant high gloss finish. Built-in 1” tile flange on 3 sides.
What does it mean when your spa says PF error?
Attempt to rest the spa power, The PF error will reset itself if power levels return to normal. Contact the dealer or service technician if the problem continues. Indicates faulty communication between the spa’s control panel and circuit board and/or remote control panel.
What should I do if my spa control panel is not working?
The connections should be inspected to ensure they are straight and sitting in place tightly. The breaker can be turned on again allowing the spa control system to reboot. If this does not help and since the sensors are brand new with no signs of defect, the problem could be a faulty circuit board.
What should I do if I get a Flo error on my spa?
Some of them may require a skilled technician to come out and work on your spa for you. 1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter.
What to do when you get a Flo code on your Arctic spa?
Please try again later. This tutorial video focuses on what to do if your Arctic spa is getting a FLO or FLC error code on your control panel. The first thing and most important thing to try is to restart your Arctic Spa by turning the breaker off and on again. Many times, this will fix the issue.
What does Flo error on my Sundance spa mean?
A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try. Sometimes we can’t see the problem with our eyes.
First determine which message you are seeing. If you are seeing a Flashing FLO message, check to see that you still have water movement ie your circulation pump is still turning/waterfall is still running, jet and blower buttons still work. If this is the case turn the GFCI breaker off to the spa and remove your filter.
Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).
What to do if your GFCI is flashing Flo?
Make sure there is nothing in the filter area and turn your GFCI back on again. If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter.
What to do if your heat pump has low voltage?
Check low voltage (24-vac R to C) at motor. Check low voltage connections (G.Y W. R. C) at motor. Check for unseated Dins in connectors on motor harness. Check motor for tight shaft. Perform motor/control replacement check. Run moisture check.
What is the position of a Flo control valve?
Automatic Flo-Control Valve Operation: depending on the valve brand and model this position may be marked as Winter or Automatic. Or the valve lever is turned fully clockwise. As we illustrate later in this article, other flow control valves will have position markings cast into the valve body and marked Open, Winter, or Closed.
What is the B & G Flo emergency heat valve?
The label on the B&G Flo Control valves at left includes instructions on which way to turn the lever. Emergency heat: the circulator pump is broken and we want hot water for heat to be able to circulate in the home by gravity until the circulator can be repaired or replaced – this is an “emergency heat” function that could be very useful.
What do you need to know about Vita spas?
Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products. Their focus on hydrotherapy includes the same level of therapeutic relief that consumers would receive by visiting a massage therapist.
Why does my Vita spa not turn on?
Overheating condition where a water temperature sensor has detected water temperatures of 110°F (43.3°C). Spa functioning is then disabled until temps fall below 108°F (42.2°C).Could indicate a pump operating at low speed for an extended time, constant filtering due to a programming error or a faulty pump. DO NOT GET INTO THE WATER!
Can You unsubscribe from a Vita spa email?
I can opt out at any time by selecting the unsubscribe option that appears at the bottom of every email. Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products.
Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products. Their focus on hydrotherapy includes the same level of therapeutic relief that consumers would receive by visiting a massage therapist.
Overheating condition where a water temperature sensor has detected water temperatures of 110°F (43.3°C). Spa functioning is then disabled until temps fall below 108°F (42.2°C).Could indicate a pump operating at low speed for an extended time, constant filtering due to a programming error or a faulty pump. DO NOT GET INTO THE WATER!
I can opt out at any time by selecting the unsubscribe option that appears at the bottom of every email. Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products.
Make sure there is nothing in the filter area and turn your GFCI back on again. If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter.
What to do if you need to leave Flo exam?
If you need to leave the exam for medical, compassionate or technical reasons, you will need to submit an Online Examinations Incident Report form. If you run into technical difficulties during your exam, please first take a moment to record the incident or difficulty, and take any useful screenshots .
What does Flo stand for in a spa code?
FLO* = Flow Switch (heater is deactivated. Pump may also be deactivated). Hold = Panel sensors have been pressed too many times in a short period of time. HOT = Circuit Board temperature has exceeded acceptable limit.
What is the error code for the spa?
PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable. Contact ACC. OHH = Overheat. Spa has shut down. One sensor has detected 118º Fat heater. OHS = Overheat. Spa has shut down. One sensor has detected 110ºF. SnA = Spa is shut down.
What’s the reset button on an old spa?
Older spas used mechanical Temperature and Hi-Limit switches. This type of Hi-Limit can usually be reset by pushing in its reset button, a red or black button located on the heater or equipment pack (see your spa manufacturer’s instruction manual for exact location on your spa).
Where is the pressure release valve on a spa?
Fortunately, once this air is released from the system, everything should work properly. If your spa’s Filter is in a sealed Filter Housing, there should be a small black pressure release valve directly on top of the housing.
Why does my hot tub have a Flo message?
The message can also be caused by soiled filters, plugged or bad Flow switches or a bad connection from the Flow switch to the PWA. In rare instances a bad PWA could cause a solid FLO message. If the pump checks out try and look at the filter, the circ line, the wiring to the Flow switch and the Flow switch.
Older spas used mechanical Temperature and Hi-Limit switches. This type of Hi-Limit can usually be reset by pushing in its reset button, a red or black button located on the heater or equipment pack (see your spa manufacturer’s instruction manual for exact location on your spa).
Why does my hot tub keep flashing Flo?
If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. It’s very important to remember that if you just finished fresh filling your spa then you could also have had an air lock that caused a Flashing FLO message.
