How to deactivate the spa lock on a hotspring?
To deactivate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-) buttons at the same time and hold them down until the word SPA and the lock symbol are no longer illuminated on the display (approximately two seconds). The TEMPERATURE LOCK feature deactivates the temperature control function of the main control panel.
How do you turn on the spa light?
To turn on the spa light, press the LIGHT plus (+) button. The light will turn on at maximum intensity and the light symbol will illuminate on the control panel display. To reduce the intensity of the light, press the LIGHT minus (-) button.
How to troubleshoot an issue with your spa?
To troubleshoot an issue with your spa, locate your specific problem in the chart below to help determine a probable cause, and then apply the right solution. Do you need to call a professional technician? Do you need to call a professional technician? Adjust the total alkalinity and pH.
How can I lower the temperature of my spa water?
To decrease the set temperature of the spa water, press the TEMP minus (-) button. Each time the button is pressed, the set temperature display will decrement by one degree. If the button is held down, the set temperature display will decrease by one degree every half-second.
To deactivate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-) buttons at the same time and hold them down until the word SPA and the lock symbol are no longer illuminated on the display (approximately two seconds). The TEMPERATURE LOCK feature deactivates the temperature control function of the main control panel.
What to do if your spa control is not working?
If only a part is not working, look for error messages or blinking lights. As a first step, reset your breaker. If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board.
What to do if your spa control panel is frozen?
If the control panel is frozen or dead, you have to check if the problem is the control panel or the circuit board. Examine if there is moisture in the display. Check if there are cracked buttons or if a part is wet. If only a part is not working, look for error messages or blinking lights. As a first step, reset your breaker.
How does the hot tub control panel work?
The hot tub control panel is like a timer that keeps the spa’s temperature constant. It turns off the spa when you forget to and troubleshoots problems. Thus, it is very important to have a spa control system in good working condition. Many issues could face your spa, including electrical issues.
Why is my spa topide control panel not working?
But there are some ways to reduce the risk… read on. Bottom line is – it could be a bad spaside control panel, or it could be a bad spa control board, or a bad cable that runs between the control panel and the control board. Or it could be fuse on the circuit board or the transformer, not sending the correct power to the topside panel.
How do you remove a spa control panel?
Slide the spatula around in order to break the silicone mounting seal of the spa control panel. If this does not easily occur, you can use a large flathead screwdriver. To prevent scratches or cracks, use a towel between the screwdriver and the silicone.
What to do if your hot tub control panel is not working?
Examine the panel to see if any moisture is inside the display. See if the panel or any buttons are cracked or if it could have possibly gotten wet. If only part of the control panel is not working, check for any blinking lights or error messages.
How to troubleshoot a spa side control panel?
Spaside Control Panel Buttons Not Working Correctly 1 Check for moisture under glass or on contacts 2 Check cable for any rodent damage, crimping or melting 3 Clean plug-in cable connections at both ends 4 Membrane or touch pad buttons may be faulty 5 Inspect circuit board for damage and correct power output 6 Replace topside control
Why is a hot tub control panel important?
A hot tub control panel acts as a timer, keeps the temperature constant, turns off the spa if you forget to, and helps troubleshoot problems with your spa. This is why it is important to keep the control panel in good working order.
Is there a way to reset the Coleman spa controls?
Sometimes, after you’ve set a custom setting, like a longer-than-default filtration period, you may want to revert back to the factory setting. You can do this by resetting the Coleman Spa controls. Set a custom filtration period.
How to troubleshoot a spa control panel problem?
Reset the control panel if it only displays dashes and not error messages. Turn the power off for one hour and then turn it back on. If the control panel is displaying strange messages or have lights blinking at the same time, it could be a software issue with the circuit board. Check if there is corrosion or condensation.
The hot tub control panel is like a timer that keeps the spa’s temperature constant. It turns off the spa when you forget to and troubleshoots problems. Thus, it is very important to have a spa control system in good working condition. Many issues could face your spa, including electrical issues.
What to do if your hot spring spa is not working?
Contact the dealer or service technician if the problem continues. Indicates faulty communication between the spa’s control panel and circuit board and/or remote control panel. Contact the dealer or service technician. Stands for “Sensor 1” and displays when the high-limit sensor is malfunctioning.
What do you need to know about spa topside control panels?
The Spa Topside control panel is used on hot tubs, portable spas, jetted tubs – just about every spa uses a display panel to allow the user to easily control the functions of a typical spa – pumps, heater, lights, blower.
