How to check spa panel messages on Balboa direct?

1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.

What to do when there is no error message on Balboa?

If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization. The “CFE” or “CONFIG ERROR” Configuration Error Appears to have been Corrected or is Intermittent.

Do you have to be a spa technician to use Balboa direct?

This is NOT intended as a service guide or a means for you, as the consumer, to service your equipment in any way. this information is being provided for informational purposes only. Any and all service should be performed by a licensed spa technician.

What does CFE or config error mean on Balboa direct?

The “CFE” or “CONFIG ERROR” Configuration Error Appears to have been Corrected or is Intermittent. If the Error Repeats, Retest the “CFE” or “CONFIG ERROR” Configuration Error or Call Balboa Technical Service for Assistance. “Cyclic Redundancy Code” (CrC) Checksum Error.

How does sleep mode work on a Balboa?

Toggle between READY and REST by pressing temp. Press light or wait for 10 seconds to go back to the Main Screen. Sleep Mode (sl) = heats to within 10 degrees (less) than preset temperature and only during the filtration cycle. Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours).

What does SL mean on a Balboa hot tub?

Sleep Mode (sl) = heats to within 10 degrees (less) than preset temperature and only during the filtration cycle. Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours). Preset cycle set from factory is F1, so if in ec or sl mode your water will not reach desired temperature.

Is there a relay fault in my Balboa spa?

4. If there is water circulation immediately after you have restored the power to your Spa (without pressing any buttons) and the Jets’ Indicator Light remains OFF, a Relay Fault in the Control System has been confirmed. To have the issue resolved, a new Balboa BP501 Control System would need to be installed.

Is there an issue with the Balboa bp501 system?

If your Spa seems to be running the low speed of the pump for extended periods of time (more than 2 hours or continuously) and you have confirmed the Filtration Cycles are currently set to run for 2:00 hours only, there might be an issue with the Balboa BP501 Control System.

Why are the red and green lights blinking on my spa?

If both red and green lights are blinking, this could indicate low water flow. Resetting the spa by turning off the power, waiting and turning it back on is likely to resolve the issue. If these troubleshooting tips don’t solve your problem, consult the owner’s manual for your controller. You can also contact the manufacturer for technical help.

What does message on Cal spa control panel mean?

A message on the control panel may indicate a problem. Note: The message troubleshooting shown here applies to Cal Spa control panels built in 2013 and earlier. Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual.

Is there a troubleshooting guide for a spa?

There are many problems spa owners can identify and resolve themselves. This troubleshooting guide will help you with many common problems and may save you a service call. We don’t expect spa owners to be technicians, so everything contained in this guide is non-technical and does not involve tools.

Why is the power button on my spa not working?

If you do not hear anything when the button is pressed the button may not be working. First cut off the power to the spa, then locate the electrical box inside the spa, it is normally located under the controls.