How to check salinity of Jandy aquapure pool?

Backwash filter if a DE filter is installed. Partially drain pool and dilute with fresh water until salinity returns to 3.0 to 3.5 gpl Unit wired to improper AC voltage. Contact a pool professional Verify proper flow/temperature/salinity sensor installation. Check salinity with Myron “L” meter calibrated for NaCl or test strips.

What does a service code on a Jandy aquapure mean?

If you have a Jandy AquaPure 700 or 1400 chlorinator, there’s a chance you may have come across a service code (or error code) before. A service code is a three digit number that appears on the display panel of an AquaPure Control Box, letting you know if your AquaPure unit is experiencing any problems.

How to change the salinity reading on aquapure?

•Press and release the “Temperature “ button within 5 seconds to enter the salinity calibration screen. •The system will display the salinity reading, press the up arrow to increase the reading and the down arrow to decrease the reading. •When the proper reading is reached press the “Temperature” button within 5 seconds to store it in memory. 15

How does the Jandy salt water pool system work?

Jandy AquaPure salt-water chlorine sanitizing systems use salt-water to deliver high-performance water sanitation with uncompromised performance, reliability, and hydraulic…

What’s the salt content of the Jandy aquapure 1400?

Funny thing, the Aqua Pure 1400 just reported 5.1 g/l. Interesting…. Looks like it doesn’t need calibration after all. Trust the SWG and Taylor test. Drain some water and get the reading to 3500. I bought the Taylor K1766 test kit and I calibrate my Aqaupure 1400 to those results twice a year.

How big does a Jandy salt water pool need to be?

Jandy AquaPure Salt Water Pool System. The PLC1400 is good for a pool size of up to 40,000 gallons, meaning if the pool system is running 24 hours a day the chlorine generated will be enough for a pool up to 40,000 gallons.

Where do I find the service code on my aquapure?

A service code is a three digit number that appears on the display panel of an AquaPure Control Box, letting you know if your AquaPure unit is experiencing any problems. Service codes are fast, easy to read, and not only identify the problem, but direct you to an available solution.

Are there fuses on Jandy aquapure salt generator?

There are no fuses, but you might check the GFI outlet if it is connected to one. If other indicators are lighting up, then it is probably a faulty display. A replacement kit is available. It’s called the Control PCB Assembly Part No. R0512300 from Jandy AquaPure Ei.

What should my aquapure salt readout be today?

Test today was 2700 PPM from the pool store and 3700-3800 reported by AquaPure. Had the same results two weeks ago at a different store. What could cause this and how to correct?

What happens to the salt level on a Jandy aquapure?

Typically, they are factory set at 75 degrees. Each degree lower will yield approximately a 200 ppm drop in what it thinks the salt level is. I think your unit is behaving as expected, Adding some additional salt will cure the alarm until the temp starts climbing. Then it will think its has too much salt.

How often should I use the Jandy aquapure 1400?

I bought the Taylor K1766 test kit and I calibrate my Aqaupure 1400 to those results twice a year. IIRC, the Aquapure uses a similar salinity test to the Pentair, conduction. Typically, they are factory set at 75 degrees. Each degree lower will yield approximately a 200 ppm drop in what it thinks the salt level is.

How much salt does an Aqua Pure give?

My Salt tester has been consistently giving me 5000PPM of salt. The Aqua Pure has been giving me 4.5g/l ~ 4500PPM. The Pool guy’s salt tests, electronic gave him a result of 4200PPM, his test strips AquaCheck (I asked him to test twice) came back at 3900 then 4200.