How much does it cost to replace Atwood levelegs controller?
My understanding is that Atwood no longer supports or manufactures the controller. Actually it is made overseas. They have a new system that would require replacement of the jacks, controller, and front panel. If I have to do that, I will go to HWH and that cost is $5,000 installed. Location:Where ever the wheels stop ?
Are there power wires on a levelegs RV?
The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem. The pins for the signal lines are on the controller board and about the size of wire wrap pins.The corrosion develops between the connector and the pins.
Is the Atwood levelegs grounded on the same bus?
It could be a poor ground, but according to the diagram, all four motors are grounded on the same buss. Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759.
How big are the power jacks on Atwood levelegs?
The size is about #22 gauge. These are signal wires only with mini Walden-Molex connectors. The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem.
How to repair an Atwood levelegs keypad for free?
Step 1 – Click the green button above to add the part and complete the RMA form. Step 2 – Print the RMA form and put it in a box with the parts for repair. Step 3 – Mail us the box for a free repair evaluation to the address below. We do not currently have any stock of new or rebuilt replacements available.
The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem. The pins for the signal lines are on the controller board and about the size of wire wrap pins.The corrosion develops between the connector and the pins.
It could be a poor ground, but according to the diagram, all four motors are grounded on the same buss. Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759.
The size is about #22 gauge. These are signal wires only with mini Walden-Molex connectors. The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem.
Where can I get an Atwood Awood controller?
Atwood Tech Service is GREAT! Do not hesitate to call if you have an Atwood problem. Other RV product mfgs. should emulate them. I need an Awood controller 66235 as mine will no longer work. Can anyone help me either repair this one or get one from a salvage yard?
What are the flashing lights on my Atwood levelegs?
Periodically, especially if the rig has been sitting for a while, my Atwood Levelegs electric jacks will refuse to retract and will display flashing green and red lights, usually in one corner, indicating which jack is having trouble.
When to use the Atwood levelegs system guide?
ATWOOD LEVELEGS SYSTEM Guides are only intended for use on Atwood™ products by service technicians who have successfully completed Atwood™ training. This guide should be used in conjunction with the appropriate Instruction Manual provided with the product and any applicable Industry Standards. This is not intended to be a complete list.
How to check voltage on an Atwood RV?
Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759. I have the Atwood Levelegs. To prevent the low voltage problem the engine must be running at a little more than idle.
When do Atwood levelegs Jacks get cranky?
It seems the jacks only get cranky when they haven’t been used in a while and they are fully extended. If you make blocks like these, I’d recommend using treated lumber, then priming and painting them, otherwise they’ll rot quickly when in contact with the ground.
Where is the red light on Atwood levelegs?
Next, try turning off the key and manually spinning the retractor nut a few turns (they’re on the end of the motors near the top of each leg and should turn fairly easily) for the leg with the blinking red light. If you take a paper towel or rag with you, you can keep your hand from getting grimy.
