How many degrees are in the Sundance Spas temperature sensor?
Fareinheit Celsius OHMSΩ 59.00 15 48840 60.8 16 46680 62.6 17 44610 64.4 18 42630
What are the manuals for the Sundance spa?
Find out how to use, care for, and program your Sundance ® spa by browsing the manuals and guides below. (2020) 880™ Series Manual – (Aspen®, Maxxus®, Optima®, Cameo®, Altamar®, Marin®, Cambria™, Capri®) (2020) 780™ Series Manual – (Chelsee®, Hamilton™, Montclair™, Bristol™, Hanover®, Dover™)
Why does my Sundance spa go into Oh error code?
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
What should chlorine level be in Sundance spa?
Your Sundance Spa is equipped with the ClearRay UV-C Water Purification System, so you are aiming to keep the Chlorine level at just 1ppm (light green on your test strip). The Sun-Boom level (the top square/first line on your test strip) will fluctuate.
What’s the start time on a Sundance 880?
880 & 980 Series: Press the “Menu” button to enter the settings menu. Select “Heat & Filter”. Select “1” for Primary Filter. Adjust “Start Time” as required and press the check mark button to confirm and activate the setting. Select 12 AM if you are planning on using 24 hour filtration.
How to set heating mode on Sundance spa 680?
Here are the instructions for setting the Heating Mode on your Sundance Spa. 680 Series: Press the “Menu” button repeatedly until you get to the “HEAT” menu. Use the temperature up or down buttons to scroll through heating options.
Why is my Sundance Spa having trouble shooting?
1. Dirty Filter: even when you have cleaned the filter, the filter may be impacted and be time for a new filter. The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter.
Fareinheit Celsius OHMSΩ 59.00 15 48840 60.8 16 46680 62.6 17 44610 64.4 18 42630
What does summer logic mean on a Sundance spa?
These are the error codes and display messages that a Sundance® Spa may display, along with what they mean and any actions required: “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather.
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
Do you need a cover guy for a Sundance spa?
If you are needing a replacement hot tub cover for your Sundance® Spa The Cover Guy is your answer. With all Sundance® Models on file The Cover Guy can easily provide you with a new hot tub cover without you having to measure.
These are the error codes and display messages that a Sundance® Spa may display, along with what they mean and any actions required: “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather.
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
What is the error code on the Sundance Spa hot tub?
Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.
How do you remove sensor from Sundance Spas?
To Remove a sensor or switch wire from the sensor harness connecto r (J6), Insert the end of a paper clip into the slot corresponding with the wire to be removed. This will depress the pin tine,allowing the wire to be pulled from the harness connector.
