How long does the Atwood water heater stay lit?
I have an Atwood water heater DSI Model G6A8E it will light for about 30 seconds then shut down. I have cleaned the tubes, checked the grounds, the ECO reads with an ohmmeter, as does the thermostat,I get a reading with the thermal cutoff (I am not to sure about this one tho.)
What happens if your pilot light goes out on your water heater?
In most cases, most water heaters tend to come with a 1 or 2-year warranty. If your pilot light malfunctions during this period, you can always go back to where you bought it and get it fixed. This is exceptionally beneficial because, in most cases, they may replace any damaged equipment or replace the water heater entirely.
Where is the pilot light on a gas heater?
The pilot light should be close to the gas burner tube, watch it closely. Ignite the flame with a long match while switching the knob to “pilot,” hold it in the position for 35 seconds. Once the pilot comes on, turn the knob back to “on.”
Why does my water heater not stay lit?
Or you didn’t run out of gas or have the water heater off for a time. If so try lighting it several times to make sure of gas flow. Sounds like a themocouple either needs cleaned or replaced. Or you didn’t run out of gas or have the water heater off for a time. If so try lighting it several times to make sure of gas flow. Click to expand…
I have an Atwood water heater DSI Model G6A8E it will light for about 30 seconds then shut down. I have cleaned the tubes, checked the grounds, the ECO reads with an ohmmeter, as does the thermostat,I get a reading with the thermal cutoff (I am not to sure about this one tho.)
Why does the pilot light on my water heater not stay on?
This feature is not available right now. Please try again later. “Cold and Helpless” in Anthem, Ariz., says the pilot light on his Atwood 6-gallon water heater stays on only when the button is depressed on the control valve. He replaced the thermocouple, but the pilot frame still will not stay lit.
What kind of circuit board do I need for my Atwood water heater?
The quickest way to test a circuit board for your water heater is to use the circuit board from your Hydroflame furnace if you have one. The 8500 or 8900 models are the most compatible with your Atwood heater and should plug in easily. There will be the same 20-second delay that happens on your furnace when you power up the water heater.
The pilot light should be close to the gas burner tube, watch it closely. Ignite the flame with a long match while switching the knob to “pilot,” hold it in the position for 35 seconds. Once the pilot comes on, turn the knob back to “on.”
This feature is not available right now. Please try again later. “Cold and Helpless” in Anthem, Ariz., says the pilot light on his Atwood 6-gallon water heater stays on only when the button is depressed on the control valve. He replaced the thermocouple, but the pilot frame still will not stay lit.
Why does the gas pilot light go out?
TOP 10 Reasons Why the Gas Pilot Light Goes Out & Won’t Stay Lit! – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.
Why does my Atwood water heater not light up?
Atwood RV Water Heater Won’t Light When this happens to the GH6-6E Atwood water heater then the source of the problem could be the regulator or the thermostat or both. The solution t this problem, if these are the source, is to replace them.
What happens if the pilot light is not lit?
Once the thermocouple detects that the pilot light isn’t lit, it turns the gas off as a safety measure. An unlit pilot can also stem from a dirty thermocouple as the dirt may be obstructing the current signal, which would also lead to a gas outage.
How to test the Atwood water heater thermostat?
How to Test Atwood Water Heater Thermostat. The best way to test this part on your water heater is by using a continuity tester. When the water is cold there should be continuity between the contacts. When the water is hot there should be no continuity.
Why does my Atwood water heater not ignite?
There are several issues behind why your Atwood Rv water heater doesn’t ignite. In this chapter, we break down every possible cause and provide the solution as well. A thermocouple is a device that senses the heat of a pilot and lets the gas flow to the burner.
The quickest way to test a circuit board for your water heater is to use the circuit board from your Hydroflame furnace if you have one. The 8500 or 8900 models are the most compatible with your Atwood heater and should plug in easily. There will be the same 20-second delay that happens on your furnace when you power up the water heater.
Why does the pilot light go out on my water heater?
A thermocouple is a device that senses the heat of a pilot and lets the gas flow to the burner. If the thermocouple is malfunctioning, it doesn’t allow the gas to run through the pilot and the burner. In return, the pilot light goes out repeatedly and would not stay lit.
This may be one of the more common sources for the heater not staying lit. Its job is to detect the flame once the flame has been lit and there are several versions of this part. You will have to have the right model number from the old part to get a new one.
What should the resistance of a water heater be?
Or you can use a VOM meter to test the resistance and for most water heaters with a 1400 watt heating element, the resistance should be just over 10 ohms. Check the base and the two probes to see if there is any resistance present. if so, the element is bad.
What is the DSi FAULT light on Atwood RV water heater?
I spoke with my contact at Dometic (who took on the Atwood water heaters) and they said that the DSI fault light on the switch for your Atwood RV Water Heater # AT94022 (GC10A-4E) will only come on for two reasons.
Why is my Eco Light not working on my water heater?
The first reason is that the water heater has attempted to ignite and failed, while the second reason is that the ECO has become an open circuit. They said to check for continuity across ECO when your light comes on to see if that is the problem. Let me know if you are still having problems and I can help you troubleshoot further.
I spoke with my contact at Dometic (who took on the Atwood water heaters) and they said that the DSI fault light on the switch for your Atwood RV Water Heater # AT94022 (GC10A-4E) will only come on for two reasons.
How do you replace an Atwood water heater?
How to Replace Atwood Water Heater Element. On some models, you will have to remove the junction box out before you get access to the heating elements. Once you have done that, you will see that the element has 2 wires attached to it. Your next step is to remove the two wires which is easily done by loosening the screws. Now for the tricky part.
Why does my Propane water heater not light?
The green light comes on on the control panel, but nothing happens – the red light doesn’t come on either. You must have something different from what I have experience with. On most water heaters there is a red light in the on/off switch that turns on when you first turn it on and again each time that it attempts to light the propane.
Why does the Atwood hydro flame furnace not light?
After that, the burner ignites and heat would steadily accumulate in the furnace combustion chamber. The air stream that circulates through the outlets would be warmed by the heat until the set temperature is reached.
