How does the ThermoSpas work in standard mode?
Pressing the ‘Pump 1’ button will change the mode to Standard and display the Economy-in-Standard icon. The spa will automatically revert to Economy mode after one hour (or instantly if you press ‘Mode/Prog’). Sleep Mode heats the spa to within 20° of the temperature set-point, but only during filtration cycles.
How to turn off pump 1 on the ThermoSpas?
Pump 1 Pump 1 is a 2 speed pump. Pressing once puts the pump into low speed, indicated on the LCD by a slow moving pump icon . Pressing a second time activates Pump 1 to high speed (icon moves faster). To turn off, press a third time (icon disappears from the LCD).
How does a hot tub control panel work?
Control Panel Operation (for additional information, please see the Special Operating Instructions for your specific hot tub) TS702 Main Control Panel Pump 1 Pump 1 is a 2 speed pump. Pressing once puts the pump into low speed, indicated on the LCD by a slow moving pump icon .
How to check spa panel messages on Balboa direct?
1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.
How big is the Olympian hot tub at thermospa?
The Olympian hot tub seats 6 adults and can be outfitted with 35-75 jets. It features a computerized control panel, titanium heater, ice bucket, underwater lighting and 3-6 spa pumps. This spa measures 93″ x 88″ x 43″.
How can I test my ThermoSpas hot tub?
ThermoSpas offers free computerized testing of your water. If you reach the point of having no luck with keeping your water in balance, and have tried draining and refilling your tub, you can send us a sample of your hot tub water for analysis. Please contact ThermoSpas Customer Care Department at 800-876-0158, option 2.
How many seats are in the thermospa spa trainer?
It has 7 seats, up to 67 rejuvenating spa jets and 4 spa pumps. The Spa Trainer is a swim spa that fits up to 12 adults. It measures 174″ x 88″ x 52.5″, with a swim section and 2 massage seats with up to 85 jets in total.
What kind of parts does Thermo SpA use?
Thermo Spas sells direct to consumers. They custom builds spas with the features or options the customer wants. Hot Tub Outpost carries a wide variety of spa parts that fit select Thermo Spa hot tubs. Thermo Spas makes 3 series of hot tubs: The Fitness Series with 3 models, the Aquatic Series with 1 model and the Designer Series with 8 models.
When does the spa go into prime mode?
When power to the spa is turned on, the Main Control Panel will display a series of diagnostic numbers and/or letters. When it displays “Pr”, it has finished initiation and enters into Prime Mode. Prime Mode will last for 4-5 minutes before automatically entering Run Mode. Run Mode can be entered earlier by pressing either
What do the warm and cool buttons do on a ThermoSpas?
Warm & Cool The warm & cool buttons are used to change the temperature set-point of the spa. When either button is pressed, “Set Temperature” is displayed on the LCD and the temperature can be adjusted. The minimum set point is 80°, while the maximum is 104°.
Pump 1 Pump 1 is a 2 speed pump. Pressing once puts the pump into low speed, indicated on the LCD by a slow moving pump icon . Pressing a second time activates Pump 1 to high speed (icon moves faster). To turn off, press a third time (icon disappears from the LCD).
Pressing the ‘Pump 1’ button will change the mode to Standard and display the Economy-in-Standard icon. The spa will automatically revert to Economy mode after one hour (or instantly if you press ‘Mode/Prog’). Sleep Mode heats the spa to within 20° of the temperature set-point, but only during filtration cycles.
Where can I get a Marquis hot tub manual?
For your convenience, Marquis has indexed our hot tub manuals and hot tub guides below. Please select the appropriate tab to download the appropriate hot tub documents (.PDF). Need help? Your local Marquis Dealer can assist you with questions about replacement parts, maintenance and other needs to keep your spa running smoothly.
How do I change the spa to standard?
The Economy icon will be displayed unless the mode is changed. Pressing the ‘Pump 1’ button will change the mode to Standard and display the Economy-in-Standard icon. The spa will automatically revert to Economy mode after one hour (or instantly if you press ‘Mode/Prog’).
