How do you reset the inverter on a magnum?
Certain faults require that the inverter be reset. To perform an inverter reset (also known as a soft reset), press and hold the Power ON/OFF button (see Figure 4-1) for approximately fifteen (15) seconds until the Charging/Inverting Status LED comes on and flashes rapidly. Once the rapid flashing has begun, release the Power ON/OFF button.
What should I do if my magnum me2012 is not charging?
It’s a direct wire on the “-” side, and a good fuse on the “+”, no shunt. You made need to do a hard reset. This next move must have all 110 volts off for the inverter and all doc power shoul be off. That is romoving the positive lead off the inverter. Now normally a 30 minute reset will do the trick.
Why does my inverter on my magnum not charge?
The inverter probably will not charge them unless it sees a certain voltage. When you touch then 12vdc lead back on it probably will have a small spark. That is ok. Just do not keep putting it on and off. No joy in Mudville.
Where is the Magnum inverter located in the coach?
Our Magnum inverter is located in the basement of our coach. It is mounted, upside down, between the main support rails of the chassis, in one of our slide out bays. The only way to get in there is to empty out the contents of the slide out and go in, back down, and attempt to work in a highly constricted area.
Certain faults require that the inverter be reset. To perform an inverter reset (also known as a soft reset), press and hold the Power ON/OFF button (see Figure 4-1) for approximately fifteen (15) seconds until the Charging/Inverting Status LED comes on and flashes rapidly. Once the rapid flashing has begun, release the Power ON/OFF button.
What are the possible problems with Magnum dimensions?
Possible problems include: a failed remote circuit fuse, a defective switch, a defective isolation relay in the circuit or open wiring anywhere in the remote on/off circuit to the inverter. Correct the fault and retest.
Why is there no fuse on my magnum?
Note: Repeated fuse failures are probably caused by either a positive cable shorted to ground (chassis) in the battery system or poor battery cable connections. Locate and correct the short or poor connection then retest the system. If no fuse is defective, the battery/charging system is suspect.
Why do I need remote control for Magnum inverter?
The ME-RC remote control allows you to monitor and customize the operating parameters to your Magnum inverter/charger. It is the same remote used on all Magnum inverter/charger models in the ME, MM, MS, and the RD Series lines so there is no cross-platform confusion.
What should I do if my dimensions inverter overloads?
Call Dimensions for assistance. Overload indicator LED on. Switch the inverter off, remove all AC loads from the inverter’s output receptacle and disconnect the AC hard wire output inside the front panel of the inverter. Switch the inverter on.
Why does my magnum inverter have AC overload?
What created the AC overload issue to occur was the simultaneous use of a Microwave, kettle and toaster being run off the same 15 Amp circuit. That action should only have tripped a circuit breaker. I have no idea why or how it wound up causing an AC overload issue on the inverter. If something like this happens to you, check with Magnum first.
What should the voltage be on a magnum inverter?
If the voltage LEDs indicate a voltage 11-12 VDC or greater, the fault lies in the optional remote on/off circuit, continue with step B below (if the inverter doesn’t have a remote on/off circuit, call Dimensions for assistance). Locate the small violet wire in the front of the inverter.
What created the AC overload issue to occur was the simultaneous use of a Microwave, kettle and toaster being run off the same 15 Amp circuit. That action should only have tripped a circuit breaker. I have no idea why or how it wound up causing an AC overload issue on the inverter. If something like this happens to you, check with Magnum first.
If the voltage LEDs indicate a voltage 11-12 VDC or greater, the fault lies in the optional remote on/off circuit, continue with step B below (if the inverter doesn’t have a remote on/off circuit, call Dimensions for assistance). Locate the small violet wire in the front of the inverter.
Call Dimensions for assistance. Overload indicator LED on. Switch the inverter off, remove all AC loads from the inverter’s output receptacle and disconnect the AC hard wire output inside the front panel of the inverter. Switch the inverter on.
