How do you remove sensor from Sundance Spas?

To Remove a sensor or switch wire from the sensor harness connecto r (J6), Insert the end of a paper clip into the slot corresponding with the wire to be removed. This will depress the pin tine,allowing the wire to be pulled from the harness connector.

What is the error code on the Sundance Spa hot tub?

Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.

What happens when Sundance spa goes into watchdog?

When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.

How many degrees are in the Sundance Spas temperature sensor?

Fareinheit Celsius OHMSΩ 59.00 15 48840 60.8 16 46680 62.6 17 44610 64.4 18 42630

What do you need to know about the Sundance Altamar?

Upgrade your spa enjoyment with an integrated Bluetooth® stereo and speaker package. Turn your connected home and smart devices into your personalized spa assistant, from adjusting key spa settings from anywhere, 24/7 to real-time energy reports and notifications to you and your dealer when your spa needs attention.

How can I tell if my Sundance spa filter is defective?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.

How much does a Sundance spa light washer cost?

SUNDANCE SPA LED LIGHT LENS WASHER SUN6540-368 $1.07 SUNDANCE SPA PILLOW, 780 SERIES – 2017+ SUN6472-719 $33.55 SUNDANCE SPA REPLACEMENT CARTRIDGE FILTER ELEMENT SUN6000-136

How can I tell if my Sundance spa heater is defective?

Flow Switch Test: You can test to see if the Flow Switch is defective by doing a continuity test on the flow switch by testing the 2 leads from the flow switch with the Pump off (no continuity) and Pump on (continuity). Do not bypass the Flow Switch: this could cause a potential dryfire of the heater and melt down of the heater system.

SUNDANCE SPA LED LIGHT LENS WASHER SUN6540-368 $1.07 SUNDANCE SPA PILLOW, 780 SERIES – 2017+ SUN6472-719 $33.55 SUNDANCE SPA REPLACEMENT CARTRIDGE FILTER ELEMENT SUN6000-136

Is there a problem with a six pin connector?

The problem for us with six pin connector (2007-2010) using the eight pin is that the physical connector is slightly different. Regardless of the number of wires there are. 2007-10 part # is 15886733 and 2011+ # is 19418403.

How do you remove a sensor from a harness?

When did Sundance Spas start making hot tubs?

Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.

Do You need cover guy for Sundance Hot Tub?

If you are needing a replacement hot tub cover for your Sundance® Spa The Cover Guy is your answer. With all Sundance® Models on file The Cover Guy can easily provide you with a new hot tub cover without you having to measure. The Cover Guy Sundance® Replacement covers are the best made covers at the best price available.

What is the model number of the Sundance jacuzzi temp sensor?

Make sure this fits by entering your model number. EASY PARTS CHECK | This temperature sensor is Jacuzzi Part # 6600-167. It is also Sundance Spas Part # 6600-167. Check your service manual to ensure compatibility with your spa

What to do if your Sundance spa heater is not turning on?

Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.

Why does my Sundance spa go into Oh error code?

Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code

Fareinheit Celsius OHMSΩ 59.00 15 48840 60.8 16 46680 62.6 17 44610 64.4 18 42630

Do you need to replace the high limit switch on a hot tub?

Measure the temperature of the high limit thermowell. If the temp inside is the same as the water temperature, you’ll need to replace the high limit switch. Test the temperature to see where the high limit trips—typically somewhere between 110°-120° F.

Is the heater disabled on a Sundance spa?

OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. This must be repaired only be a Sundance Spas dealer or qualified service technician. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional.

Is there an O-ring for Rio 650 sensors?

This particular brand Rio 650 produced a vast variety of different sensors, and though most do not require anything external, some used an O-ring. If feeling unsure of the installation, a little silicone can be used to seal the opening. Since the quantity of silicone required is not much, clear silicone would be sufficient.

Where is the temperature sensor on the l700c spa?

If feeling unsure of the installation, a little silicone can be used to seal the opening. Since the quantity of silicone required is not much, clear silicone would be sufficient. Since the heater does not shut down at the set temperature, where is the temperature sensor located on the L700C spa?

What does the Sundance spa temp sensor 6600-167 do?

The Jacuzzi Spa Temp Sensor 6600-167 is a service part intended for professional repair and maintenance of both Sundance Spas and Jacuzzi hot tubs. This part does not include O-ring 6540-228 (sold separately). This part fits multiple models and years of Sundance Spas and Jacuzzi.

Can a bad temp sensor cause a spa to stop working?