How do I reset my Nautilus pool cleaner Dolphin?
With your Dolphin in use, press the “Reset” button. Hold the “Reset” button down for about 3-5 seconds. Check the Full Filter Light indicator, ensuring that it’s off. In essence, what you’ve just done is “zero” out the sensor.
How do I turn on my Nautilus pool cleaner?
TURN POWER ON – Press the ON/OFF switch on the Power Supply. The Cleaner will start to operate. Note: Four LEDs will light up in the corners of the switch indicating that the power is on.
How do you troubleshoot a Maytronics dolphin?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off.
- Unplug the power supply.
Why is my dolphin pool vacuum not working?
Inspect the impeller for debris and remove; clean the filters. Restart the cleaner; press and hold the reset button until the light goes off (approximately 5 – 20 seconds). If light still does not go off, take your Dolphin to your local dealer or call Maytronics Customer Service.
Why is my dolphin pool cleaner not turning on?
There may be a problem with the blue cable or the Dolphin cleaner itself. Take it to your local dealer for further testing or call Maytronics Customer Service. If your power supply unit’s “POWER/ON” button does NOT light up at all, you may need a replacement power supply.
How long is Maytronics warranty?
3 years
Maytronics warrants that your Premier Dolphin pool cleaner will be free from defects in material and workmanship for 3 years. To prove how serious we are about delivering the best-in-class high performance robot, the Dolphin Premier is backed by the very best warranty in the industry.
Why is my dolphin pool cleaner not working?
When your pool cleaner is not working or starting then it is sure that the issue is related to the power connection. One of the possible reasons for this inconvenience is because of some fault in the power supply cable of the Dolphin Nautilus CC Plus.
Why is my Maytronics dolphin pool cleaner knotting?
Knotting is definitely the main problem in non-swivel wires. In case the power cord is okay then consider it could be a mechanized issue in the cleaner. It may be a matter with motor, tracts and belts or one of the many elements associated with a swimming pool cleaner’s movements.
Why does my dolphin Nautilus pool sweeps spin?
I have a Dolphin Nautilus pool sweeps and have had Leslie Pool work on it now for 3 times, they have replaced the motor, controller and power cord but … The propeller spins, but the unit does not move. There are no obstructions as I replaced the drive tracks. Both tracks spin when out of the water.
How can I get My dolphin out of my Pool?
• Try placing the Dolphin in the pool from a different location. • The filters may be dirty. Try running the cleaner without the bag or cartridge filters. If the cleaner climbs the wall, thoroughly clean the filters before putting them back in the cleaner. • Scrub the pool floor.
How to troubleshoot a dolphin pool cleaner breaker?
Check power to the socket and reconnect Pool Cleaner Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box Turn the power supply off. Wait 30 seconds then turn it back on Unplug the power supply.
Can a dolphin pool cleaner be left in standing water?
Do not leave the power supply in standing water as this will damage the internal components. Do not allow the power supply to be submerged in the pool. Can I use my Dolphin pool cleaner with an extension cord or surge protector? The Dolphin is not designed to be used with an extension cord.
I have a Dolphin Nautilus pool sweeps and have had Leslie Pool work on it now for 3 times, they have replaced the motor, controller and power cord but … The propeller spins, but the unit does not move. There are no obstructions as I replaced the drive tracks. Both tracks spin when out of the water.
How to troubleshoot a Maytronics pool cleaner problem?
Check power to the socket and reconnect Pool Cleaner Turn the power supply off. Wait 30 seconds then turn it back on Unplug the power supply. Open the impeller cover and check that nothing is trapped in the impeller After the Pool Cleaner starts moving observe it for several minutes and make sure that it keeps moving.
