How can I recalibrate my Goldline pool panel?
You can do this by purchasing a salt meter or salt water test strips, or take the more practical approach of visiting a local pool store with a water sample. Any good pool store will do computerized water testing and salt checks. If your salt reading is different from that of the pool stores we will recalibrate your cell to the pool stores reading.
What does default mean on Goldline SWG panel?
Press the diagnostic button once. Default = what the unit thinks the salt level is due to an average of all previously recorded “instant salt readings†from all of the different polarity changes since the system was installed, or since the last time the unit was recalibrated.
What is the default display on Aqua logic?
Turn power on at the main panel and turn the Aqua Logic control power circuit breaker on. The keypad will show the default display. The default display alternates between the day/time, air and pool (or spa) temperature, pool/spa sanitizer setting, and salt level.
What kind of control system does Pro Logic use?
Pro Logic is a scalable, flexible line of Total Pool Management controls that suits any backyard environment.
You can do this by purchasing a salt meter or salt water test strips, or take the more practical approach of visiting a local pool store with a water sample. Any good pool store will do computerized water testing and salt checks. If your salt reading is different from that of the pool stores we will recalibrate your cell to the pool stores reading.
Press the diagnostic button once. Default = what the unit thinks the salt level is due to an average of all previously recorded “instant salt readings†from all of the different polarity changes since the system was installed, or since the last time the unit was recalibrated.
Pro Logic is a scalable, flexible line of Total Pool Management controls that suits any backyard environment.
What does no flow mean on a Goldline pool pump?
If the pump is not running, the system will show “NO FLOWâ€, if flashing this is just a warm up process and the unit is waiting for the water to begin moving through the cell to carry the chlorine out to the pool. Once flow is established the unit should begin to display the “POWER†& “GENERATING†lights solid green.
How to reset the Goldline / Hayward SWG panel?
To reset these light just push the black selector button in for 3 to 5 seconds and this will reset the trouble lights. After about an hour my readings were… Average 3200 and instant 3400 which is more in line with my tests. This also removes all past salt averages that may be in memory.
When does a Goldline sodium chlorinator shut down?
Goldline cells will shut down when the current draw gets above 8 amps which can happen with high salt levels and certainly 4400 ppm would shut down the unit. This is done to protect the power supply from high current which can damage components. Also, these units will usually not read high salt unless there is really too much salt.
How to change temperature on Goldline SWG panel?
If you need to change the reading, press the diagnostic button once to display the temperature. Then slide the switch up to “SUPER CHLORINATE†for a few seconds, as long as the “SUPER CHLORINATE†light illuminates, you can switch back, this should be instantaneous. This procedure will toggle between the two different settings.
Is it normal for Goldline units to be off 600 ppm?
It is normal for the Goldline units to be off as much as 600 ppm from a chemical test because they are measuring conductivity and not chloride ions. The older units were not temperature compensated so that could introduct another error when compared to a temperature compensated meter. It is acceptable.
To reset these light just push the black selector button in for 3 to 5 seconds and this will reset the trouble lights. After about an hour my readings were… Average 3200 and instant 3400 which is more in line with my tests. This also removes all past salt averages that may be in memory.
If you need to change the reading, press the diagnostic button once to display the temperature. Then slide the switch up to “SUPER CHLORINATE†for a few seconds, as long as the “SUPER CHLORINATE†light illuminates, you can switch back, this should be instantaneous. This procedure will toggle between the two different settings.
How much does Hayward Goldline Aqua rite main PCB weigh?
This main PCB is designed to use with Hayward Goldline Aqua Rite salt chlorine generator model AQR. Weight 25 pounds. Would you like to tell us about a lower price? Pages with related products.
