Can you adjust the spring tension on a slide topper?
The spring tension on the slide topper can be adjusted but you must do it carefully because there is considerable energy in the stored spring if it were to get away from you. The following link will take you to a document that describes the proper, and safe, procedure for adjusting the slidetopper tension and replacing fabric.
How to adjust slide topper on awnings?
Adjusting slide topper awnings is fairly simple. Usually takes 2 people. The roller has a spring in it. Move slide out. Look for the pin hole near end of roller. Put a cotter pin in the hole. Make sure it will not fall out. Remove end cap or mount. Roller should now be free of mounting hardware. Run slide in about 12″. Roll up topper on roller.
What does a slide topper do on an RV?
To counter this, most slideouts now come with slide toppers. Slide toppers are nothing more than a spring loaded roller mechanism with a fabric material that will wind up when the slide is retracted and unroll to cover the top of the slide as when it is extended. Any debris laying on top will simply fall off when the topper rolls up.
Why does my slide topper keep falling off?
Any debris laying on top will simply fall off when the topper rolls up. Eventually the fabric will wear and require replacement. Also, springs can lose tension over time and the effects of wind billowing can be noticed as the material flaps around in the wind when the slide is extended.
How to adjust tension on Dometic slide awning?
Loosen the left arm, pull it out just enough to clear the slide. Be very careful there is a lot of tension on the arm. With great ease turn the arm counter clock wise. One turn may give you the desired tension. if not turn arm one more turn. This should increase the tension on the Awning.
Can you tighten roller spring on carefree slide topper?
Tightening will depend on which Awning you have. When looking at the awning the bracket/brace/support arm on your right will be the side that connects to the roller spring. If the spring is not broken you can, with great caution, unbolt the arm. Before doing this, contact Carefree and find out how many turns it takes to tighten the roller spring.
How many turns to set the tension on a solera slide topper?
Hello, There are 2 replies on your site which appear to be related to how many turns are required to properly set the tension on a Solera Slide Topper.
The spring tension on the slide topper can be adjusted but you must do it carefully because there is considerable energy in the stored spring if it were to get away from you. The following link will take you to a document that describes the proper, and safe, procedure for adjusting the slidetopper tension and replacing fabric.
Do you need to adjust the tension on an RV slide out awning?
And RVs with slide-outs, a compartment that extends out from the main cabin providing extra living quarters, are sometimes made with awnings over the slide-out. In order to get the awning up and stable, the tension needs to be adjusted to get the fabric taut. Different RV makers use different awning systems.
How is the tension applied on a solera slide topper?
When installing/adjusting the Solera RV Slide-Out Awning # LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn’t billow in the wind or leave enough slack that it sags when collecting some rain water.
Tightening will depend on which Awning you have. When looking at the awning the bracket/brace/support arm on your right will be the side that connects to the roller spring. If the spring is not broken you can, with great caution, unbolt the arm. Before doing this, contact Carefree and find out how many turns it takes to tighten the roller spring.
How to increase tension on an awning slide?
Be very careful there is a lot of tension on the arm. With great ease turn the arm counter clock wise. One turn may give you the desired tension. if not turn arm one more turn. This should increase the tension on the Awning. 1. Open slide 6″-10″
Where are the spring locking pins on an ervice slideout cover?
The spring locking pins must be inserted before continuing otherwise the roller tube can spin out of control and cause personal injury and/or property damage. 2. (Detail B)On the right end of the roller tube, insert a spring locking pin through the roller bearing and spindle; it may be necessary to twist the roller to align the holes.
How to re-tension an RV awning spring?
RV Awning Repair: Re-tensioning the Spring. Step 1 – Prepare to Re-insert the Cotter Pin. When you release the tension in the spring, the cotter pin that is inserted in the holes in the awning Step 2 – Wind the Spring. Step 3 – Re-insert Cotter Pin. Step 4 – Replace Arm and Bolt. Step 5 –
