Are there two relays for the slideroom motor?
Missing a circuit to supply power to slideroom motor.The drawing pictures one relay to power the in and out voltage to the motor- there are 2 power relays.
What should you know about the slideout room?
ALWAYS MAKE SURE THAT THE SLIDEOUT ROOM PATH IS CLEAR OF PEOPLE AND OBJECTS BEFORE AND DURING OPERATION OF THE SLIDEOUT ROOM. ALWAYS KEEP AWAY FROM THE SLIDE RAILS WHEN THE ROOM IS BEING OPERATED. THE GEAR ASSEMBLY MAY PINCH OR CATCH ON LOOSE CLOTHING CAUSING PERSONAL INJURY.
What kind of motor does a slideout use?
Slideout electrical is mainly powered by a particular electric motor driving a gear system. They are intended on lighter and smaller slide outs. They should not be overloaded for them to work effectively. Engineer and integrate them into the RV properly.
Where is the slide out controller on a motorhome?
For my motorhome, there are two slide out controllers attached to the “roof” of the middle basement compartment between the two main beams of the frame. One controller for the passenger side slide-out and one for the drive side slide-out. RV Masters charged $130 for the new controller and $140 for an hour of labor to install the controller.
Missing a circuit to supply power to slideroom motor.The drawing pictures one relay to power the in and out voltage to the motor- there are 2 power relays.
Why does my slide not retract after new motor?
After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.
What kind of motor does an electric slide out use?
Electric slideout uses an electric motor to drive a slideout gear system in your RV or camper. This motor is powered by a 12-volt system and needs a certain amount of amps to function. If you have many devices turned on while trying to pull out the slide, you may have a problem with overwhelming the circuit.
Why do I have an open slideout on my RV?
If you don’t have enough power coming in, you could start overworking your slideout’s motor until it overheats. This is how you will end up being stuck with an open slideout. Now, let’s get into details!
If you don’t have enough power coming in, you could start overworking your slideout’s motor until it overheats. This is how you will end up being stuck with an open slideout. Now, let’s get into details!
Electric slideout uses an electric motor to drive a slideout gear system in your RV or camper. This motor is powered by a 12-volt system and needs a certain amount of amps to function. If you have many devices turned on while trying to pull out the slide, you may have a problem with overwhelming the circuit.
What happens if you push the slide out button?
If you push your slide-out button and nothing happens, double check to make sure that the path of the slide out is unobstructed. A stray item wedged in your slide out can be an easy fix, so go check before tearing your motorhome apart looking for the slide motor.
What kind of battery does an RV slide out use?
You have enough power supply. RV’s slideout system is operated by a 12 volt DC electric motor and you need to make sure that you supply it with enough power through a converter or a fully charged 12-volt battery. Your vehicle is leveled. You need to level your vehicle before operating the slideout.
Can a single pump be used to retract slide outs?
In either instance you will probably find yourself at the mercy of an RV repairman, who may or may not have the parts needed for a quick repair on hand. Also, due to the inherent power of hydraulics, a single pump/motor is often used to extend/retract all slide-outs. When it works, you’re golden.
What are the colors of the slide out switch?
It makes sense that there is a relay somewhere as the wires on the back of the slide out control switches are different colors (orange “slide in” wire, blue “slide out” wire, and a common purple wire for all three switches). Somewhere the orange and purple wires at the control switch change to green and yellow wires at motor.
Is there an electrical problem with the slide out?
Finding an apparent electrical button, the control panel was removed and the wires for the stuck slide were placed on another slide “in/out” button. Again, there was no power to the stuck slide when the “In” was pushed. The two young mobile repair techs were now perplexed and did not have the skill to trouble-shoot the electrical issue.
In either instance you will probably find yourself at the mercy of an RV repairman, who may or may not have the parts needed for a quick repair on hand. Also, due to the inherent power of hydraulics, a single pump/motor is often used to extend/retract all slide-outs. When it works, you’re golden.
Finding an apparent electrical button, the control panel was removed and the wires for the stuck slide were placed on another slide “in/out” button. Again, there was no power to the stuck slide when the “In” was pushed. The two young mobile repair techs were now perplexed and did not have the skill to trouble-shoot the electrical issue.
It makes sense that there is a relay somewhere as the wires on the back of the slide out control switches are different colors (orange “slide in” wire, blue “slide out” wire, and a common purple wire for all three switches). Somewhere the orange and purple wires at the control switch change to green and yellow wires at motor.
Why is my slide out not working on my car?
To get back home to Katy, the power supply wires to the motor were “reversed” so the slide could be retracted so I could drive home to Katy, TX. With the power supply wires “reversed”, the slide will now not extend.
What to do if your slideout room does not lock?
Install the transit bars to the slideout room (if so equipped) and take the unit to an authorized dealer for service. Warning! WHEN THE MOTOR BRAKE IS DISENGAGED THE SLIDEOUT ROOM WILL NOT LOCK INTO PLACE; THEREFORE, THE ROOM WILL NOT BE SEALED.
Where is the slideout controller on an RV?
Locate the slideout electrical controller (refer to your dealer or RV manufacturer for location). There are two versions of the controller. For version 1, unplug the (6) pin wiring harness from the controller. For version 2, remove one of the motor leads, either the motor I or motor II lead from the controller. 3. Locate the slideout motor.
What kind of switch do I need for slide out?
Magnetic switches are very commonly used for the sensor circuits stop point. (They do not fail often) The setup should have 2 high current relays – one for the extend and one for the retract function. Is the bathroom wall between the slide in question? or some other space/wall at one end of the slide.
For my motorhome, there are two slide out controllers attached to the “roof” of the middle basement compartment between the two main beams of the frame. One controller for the passenger side slide-out and one for the drive side slide-out. RV Masters charged $130 for the new controller and $140 for an hour of labor to install the controller.
What kind of wires are in a slide out motor?
All that I saw were the green and yellow wires coming out of the wire bundle that connected to the motor’s black and red wires (see the motor photo above).
How many relays are in a 6 way fuse box?
Automobile 6-Way Relay Fuse Box, with 6 ATC/ATO fuses, 5-pin 12VDC 40A relays, 1 RTT7121 Relay. Allows You to Install car 6-Way Fuse Box Easily and Quickly.
Where are the fuses on a ram truck?
Fuse box diagram (fuse layout), location and assignment of fuses and relays Ram Trucks 1500, 2500, 3500 (2013, 2014, 2015, 2016, 2017, 2018). Before replacing a fuse check that the key has been removed from the ignition and that all the services are switched off and/or disengaged.
Which is an example of an open relay?
Example 1. 4 pin (normally open) relay with the switch on the positive side of the control circuit. Example 2. 4 pin (normally open) relay with the switch on the negative side of the control circuit. Note: These circuits have been simplified to illustrate the function of a relay and therefore exclude fuse protection that would be required.
Where do you run the wire from a relay?
The diagram shows two leads coming from the relay. Then I run the second wire of the lights or other accessory to a good ground on the frame of the vehicle. If the wires will not be soldered together and crimped connectors will be used it’s a good idea to put a dielectric paste on the connectors where they come in contact.
How do you connect a light relay to a battery?
Then run a heavy gauge wire from the battery to the relay placing a 30 Amp fuse in line very close to the battery. Do not connect the power to the battery until all wiring is done. Then I run a single heavy gauge wire out to the lights or other accessory.
What kind of relay do I need for my 4×4?
The switch that is installed in the cab of your 4×4 actually only powers the relay itself which draws very little current. In most installations a 30 AMP relay from Radio Shack (Auto Relay Cat. Number 275-226) will do unless your amperage demands exceed 30 amps. I like to used a lighted switch in the cab to let me know if driving lights are on.
Where can I find a relay 4 pin wiring diagram?
Honestly, we also have been noticed that relay 4 pin wiring diagramis being one of the most popular field right now. So that we attempted to find some great relay 4 pin wiring diagram graphic for your needs. Here you go. we found it from reliable on-line resource and we love it.
How to wire a 12V relay switch diagram?
12v relay wiring diagram 5 pin luxury a type od part v wire diagram Architectural wiring diagrams action the approximate locations and interconnections of receptacles, lighting, and steadfast electrical services in a building.
All that I saw were the green and yellow wires coming out of the wire bundle that connected to the motor’s black and red wires (see the motor photo above).
Why is my passenger side slide not retracting?
My trip to Baton Rouge for LSU football this past weekend went to heck when my passenger side slide would not retract (we stayed Thursday night in Lake Charles, LA to visit my son’s family). After calling a couple of Lake Charles RV repair shops, the initial thought was the slide motor had quit working.
Is there a replacement motor for a disco slideout?
All disco owners are in sympathy with you and would all say the replacement motor is worth the $. On the Disco, the driver side slide fits flush to the floor when extended. The three men are getting it over the ramp to retract. There is a replacement motor with higher torque available.
Why is my RV slide not going all the way out?
RV Slide will Not Go all the Way Out Most RV problems can be solved by looking for simple obstacles or obstructions first. If this problem is happening to your kitchen slide out then you may have some plumbing lines or other kitchen equipment in the way.
My trip to Baton Rouge for LSU football this past weekend went to heck when my passenger side slide would not retract (we stayed Thursday night in Lake Charles, LA to visit my son’s family). After calling a couple of Lake Charles RV repair shops, the initial thought was the slide motor had quit working.
How to troubleshoot the Lippert electric slideout system?
TROUBLESHOOTING The Lippert Electric Slideout Systemis only one of four interrelated slideout room system components. These four components are: chassis, room, coach, and Lippert Electric Slideout System. Each one needs to function correctly with the others or misalignment problems will occur.
Magnetic switches are very commonly used for the sensor circuits stop point. (They do not fail often) The setup should have 2 high current relays – one for the extend and one for the retract function. Is the bathroom wall between the slide in question? or some other space/wall at one end of the slide.
What causes the fuse to blow on a slideout?
Any perceived drag on the movement could cause the fuse to blow. Lastly, check the battery wiring connections, especially on the ground side of that circuit. I’m not aware of any inherent deficiencies with your coach, but in some cases an undersized ground cable anywhere in the circuit could cause overheating which could also blow the fuse.
What to do when slide outs don’t move?
Make sure the house batteries are charged completely, or if at all possible, plug your RV into shore power. This will indicate whether the problem may be the batteries or not. If you push the button for the slide outs and can hear the motor running but the slides don’t move, check the motor’s shear pins.
If you push your slide-out button and nothing happens, double check to make sure that the path of the slide out is unobstructed. A stray item wedged in your slide out can be an easy fix, so go check before tearing your motorhome apart looking for the slide motor.
When do you press switch, slide out does not go out?
When they press the switch to let the slide out. It makes a … read more mechanically..electronic slide outs and one will not go out. How do I mechanically get the slide out to move.
What does it mean when your Slide Room is not working?
This is an indication that there’s an obstruction in the hydraulic system. To help you figure out next steps after you determine the problem lies in the hydraulic system, RV expert Dave Solberg walks you through a quick inspection of the underside of the slide room.
Make sure the house batteries are charged completely, or if at all possible, plug your RV into shore power. This will indicate whether the problem may be the batteries or not. If you push the button for the slide outs and can hear the motor running but the slides don’t move, check the motor’s shear pins.
Where are the slide controllers on a coach?
Different coach but my slide controllers are behind a panel that holds my cable/sat input in one of the bays. I have electric motors also that look identical to yours. Mine are Kwikee but like stated all owned by Lippert now. On my motors there is a 3/4 inch nut and also on the motor is a “lock” switch.
What do you need to know about electric slideout system?
1. Level the unit. 2. Verify the battery is fully charged and hooked-up to the electrical system. 3. Remove the transit bars (if so equipped). 4. Press and hold the IN/OUT switch (Fig. 1B) in the OUT position until the room is fully extended and stops moving. 5. Release the switch, which will lock the room into position.
Different coach but my slide controllers are behind a panel that holds my cable/sat input in one of the bays. I have electric motors also that look identical to yours. Mine are Kwikee but like stated all owned by Lippert now. On my motors there is a 3/4 inch nut and also on the motor is a “lock” switch.
After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.
Can a flipped circuit breaker cause a power shutdown?
Going through this process can save you a ton of time later on if you discover the problem was there all along. Once you’re sure the problem isn’t a flipped circuit breaker, start the hunt for every GFCI outlet in your home. Even if the outlet is on the other side of the house, it can be the reason for your power shutdown.
Where are the slide out relay controls in the bedroom?
Back in the bedroom, there’s a 12V light switch right next to the bedroom slide control. I took both of them off the wall, removed the 12V supply wire from the light switch (used my meter to determine which was which), applied the 12V wire to the center pole on the slide switch…voila, bedroom slide works.
Where are the slide out relay controls in irv2?
I took both of them off the wall, removed the 12V supply wire from the light switch (used my meter to determine which was which), applied the 12V wire to the center pole on the slide switch…voila, bedroom slide works. (Engine was running and parking brake applied).
Where are the slide out relay controls on a Ford F53?
Google search also turned up a helpful doc, the Ford doc for people building motorhomes (or whatever) on the F53 chassis… This doc includes a description of all the fuses in the chassis fuse block down by the drivers left foot. I also did what voguem suggested as a test.
